Sharp EBR-4900W Инструкция - Страница 2

Просмотреть онлайн или скачать pdf Инструкция для Микроволновая печь Sharp EBR-4900W. Sharp EBR-4900W 17 страниц. Built-in kit
Также для Sharp EBR-4900W: Руководство по установке (16 страниц)

Печатать страницу
Sharp EBR-4900W Инструкция
1. (For U.K. use)
A cut-out w ill have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The m ains plug m ust be accessible after installation or an all-pole sw itch disconnection m ust be
provided w ith a contact separation of at least 3 m m in each pole.
(For Continental use)
The electric outlet m ust be installed at 150 m m high from the floor of the built-in cabinet and at 50 m m
from the right w all of the built-in cabinet as show n in Fig. 1. The m ains plug m ust be accessible after
installation or the oven m ust be connected to an electric circuit provided w ith an all-pole sw itch (contact
gap no less than 3 m m ) to disconnect the oven in case of danger. A safety-device such as a fuse in the
installation m ay be used as a sw itch.
2. Rem ove the built-in kit from the package.
3. Set the spacing brackets
a distance of 17 m m betw een the front end of the shelf and the spacing brackets, and attach them
w ith the four screw s
Caution:
4. Rem ove one screw
the tab of the back plate
5. Loosen tw o screw s
6. Install the exhaust duct
5) as show n in Fig. 3.
7. Insert the tab of the back plate
rear of the oven w ith one screw
Caution:
8. Rem ove screw
9. Let the power supply cord pass through the hole of the lower side of the intake duct
10. Install the intake duct
in Fig. 4.
Caution:
11. Rem ove the backing paper from the three cushions
left side of the intake duct
show n in Figs 5-a and 5-b. Attach the cushion
12. (For U.K. use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the pow er supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.
13. Connect the oven to the pow er supply.
Caution: a. In the U.K., connect the oven to the pow er supply 230-240 V, 50 Hz.
14. Adjust the position of the oven so that the feet fit into the recesses of the spacing brackets as show n in
Fig. 2.
Caution:
15. Place the built-in fram e elem ent
horizontally. Secure loosely to the kitchen cabinet w ith tw o screw s
16. Insert tw o built-in fram e side elem ents
Secure tw o screw s
left built-in fram e side elem ents
Note: Align parts
17. Install the second built-in fram e elem ent
the oven. Secure the built-in fram e elem ent
to the kitchen cabinet w ith tw o screw s
Caution:
Downloaded from:
http://www.usersmanualguide.com/

INSTALLATION INSTRUCTIONS

1
on the shelf along the right and left w alls of the kitchen cabinet, keeping
9
, as show n in Fig. 1.
The arrow m arks on each spacing bracket should be pointing tow ards you.
E
holding the back plate
F
from the slit of the rear of the oven.
G
H
and
holding the outer w rap to the rear of the oven as show n in Fig. 3.
2
to the rear of the oven by tightening tw o screw s
F
into the slit of the rear of the oven. And install the back plate
E
E
Fasten screw
loosely for step 10.
J
from the oven as show n in Fig. 3.
3
to the rear of the oven w ith tw o screw s
Avoid pinching the pow er supply cord betw een the oven and the intake duct
3
and attach the cushion
b. In the Continent, connect the oven to the pow er supply 230 V, 50 Hz.
M ake sure that the pow er supply cord does not touch the air vent openings behind the oven.
7
0
tightly as show n in Fig. 6. Check location by m easuring distance betw een right and
8
7
8
and
as indicated in Fig. 6. Such that screw s
M ake sure that the 7.5 m m of the fram es (upper and low er) and cabinet overlap each other
as show n in Fig. 8, or the kitchen cabinet door m ay touch the built-in fram e elem ents.
F
to the rear of the oven as show n in Fig. 3. And release
(rem oved at step 4) as show n in Fig. 3.
4
5
,
and
6
at the left side of the cushion
4
at the top of the oven as show n in Figs 5-a and 5-b.
on top of the oven m aking sure that it is level both vertically and
8
betw een the built-in fram e elem ent
. The distance is stated in Fig. 7.
7
over the built-in fram e side elem ents
7
through the holes of the built-in fram e side elem ents
0
as show n in Fig. 6.
2
G
H
and
(loosened at step
3
as shown in Fig. 4.
E
J
and
(rem oved at step 8) as show n
6
5
. Attach the cushion
5
and the oven as
0
as show n in Fig. 6.
7
and the kitchen cabinet.
0
can be fixed into position.
8
at bottom edge of
F
to the
3
.
at the top and
8