Sharp Aquos LC-22SB280UT Руководство по эксплуатации - Страница 19
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для ЖК-ТЕЛЕВИЗОР Sharp Aquos LC-22SB280UT. Sharp Aquos LC-22SB280UT 36 страниц. Liquid crystal television
Также для Sharp Aquos LC-22SB280UT: Руководство по эксплуатации (31 страниц)
Печатать страницу
Watching TV
Preparation
• POWER indicator (Green): The TV is on. ("Please wait"
will appear for a few seconds on the screen.)
Turning .on.the. power
Press POWER on the TV, or POWER on the remote
control.
TV status indicator (POWER)
Perform the following steps before you press POWER
on the remote control unit.
1
Insert the batteries into the remote control unit.
(See page 8.)
2
Connect the antenna cable to the TV. (See page
12.)
3
Plug in the AC cord to the AC outlet. (See page 7.)
To select a 4-digit channel number (e. g., Channel 22.1):
Press
2~2~
• (DOT)
~1
To select a 3-digit channel number (e. g., Channel 115):
Press
1~1~5
Method 2
Using remote control buttons
0-9, •
(DOT) to select
channels for VHF/UHF/CATV/DIGITAL, then press
ENT or ENTER.
Changing channels
To select a 1 or 2-digit channel number (e. g., ChannelS):
Press 5
Turning off the power
Press POWER on the TV, or POWER on the remote
control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator on the TV changes to off.
RmD
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when POWER
is turned off.
You can change channels in several ways.
Method 1
Using CH
+/-
or A/Von the remote control unit or on
the TV.
RmD
• If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
If you use channel-down, it will move in reverse, from the
digital channel to the analog channel.
RmD
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
RmD
• When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
• If you press 0 by itself in "Air" reception, nothing will
happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will
be made if there is no operation within a few seconds.
Lighting (Green)
OFF
OFF/Standby
ON
A"toSetup
The Auto Setup menu appears the first time you
turn on the TV, and assists you to select the menu
language, specify the Air/Cable setting, and program
your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV
system connection is made!
1
The turn on the TV, press POWER (POWER indicator on
the front of the unit changes green. It may take approx.
10 seconds for a picture to appear on screen.).
2
The "Auto Setup" function begins. Press
~/~
to select
your desired language.
3
Press
Ji,,/T
to select "Signal Type", then press
~/~
to
select "Cable" or ''Air''.
Air:
VHF/UHF channels
Cable: CABLE TV channels
4
Press
Ji,,/T
to select "Automatic Search", then press
~
or
ENTER.
5
The TV will begin memorizing all the channels available
in your area.
• It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a bar display
may not advance for several minutes, please be
patient.
RmD
• If you press ENTER in the process of "Auto Setup", the
Auto Setup stops and changes to the normal screen.
• When you make a menu selection, your changes occur
immediately. You do not have to press EXIT to see your
changes.
@-18