Digital Home System DHS-ZW-SNMT-01 Руководство пользователя - Страница 12
Просмотреть онлайн или скачать pdf Руководство пользователя для Аксессуары Digital Home System DHS-ZW-SNMT-01. Digital Home System DHS-ZW-SNMT-01 14 страниц. Z-wave motion sensor
Печатать страницуAppendix
Indication mode
The indicator light gives various statuses of the device as follows:
1. Ready for learn mode:
2. Learn in progress (add):
3. Learn in progress (remove):
4. Learn mode success:
5. Learn mode failed:
6. Tamper pressed/released:
7. Mounting successful:
Technical Speci cations
NOTE:
This part of the Instructions contains advanced details about the Sensor and its con-
guration parameters and supported Z-Wave commands.
This can be used for advanced con guration and integration not only with Vera but
with other Z-Wave controllers or gateways.
Supporting Command Classes
Basic type: BASIC_TYPE_ROUTING_SLAVE
Generic type: GENERIC_TYPE_SENSOR_BINARY
Speci c type: SPECIFIC_TYPE_NOT_USED
Listening: False, Z-Wave Lib: 4.51
Class: 0x30 COMMAND_CLASS_SENSOR_BINARY
Class: 0x31 COMMAND_CLASS_SENSOR_MULTILEVEL
Class: 0x60 COMMAND_CLASS_MULTI-CHANNEL_V2
Class: 0x70 COMMAND_CLASS_CONFIGURATION
Class: 0x71 COMMAND_CLASS_ALARM
Class: 0x80 COMMAND_CLASS_BATTERY
Class: 0x84 COMMAND_CLASS_WAKE_UP
Class: 0x85 COMMAND_CLASS_ASSOCIATION
Class: 0x86 COMMAND_CLASS_VERSION
Class: 0xEF COMMAND_CLASS_MARK
Class: 0x20 COMMAND_CLASS_BASIC
Class: 0x31 COMMAND_CLASS_SENSOR_MULTILEVEL
12
indicator light blinks every second
indicator light 2 times every second.
indicator light 3 times every second.
indicator light is on for one second.
indicator light blinks 8 times rapidly.
indicator light blinks 3 times rapidly.
indicator light is on for 1 second.
Not listening Routing SLAVE
This Z-Wave product will be used as routing slave. Slave nodes are nodes in a Z-Wave net-
work that receive commands and perform actions based on the command. This device will
always be in sleep mode because it works on batteries. In sleep mode the device is not active
listening, the device will wake up according to the wakeup command class.
Include Initiator
The include initiator is used when Primary and Inclusion Controllers include nodes into the
network. When both the include initiator have been activated simultaneously the new node
will be included to the network (if the node was not included previously).
Exclude Initiator
The exclude initiator is used by Primary Controllers to exclude nodes from the network.
When the exclude initiator and a slave initiator are activated simultaneously, it will result in
the slave being excluded from the network (and reset to Node ID zero). Even if the slave was
not part of the network it will still be reset by this action.
Z-Wave compatibility
Because this is a Z-Wave device, it means it can co-operate with other Z-Wave devices of
other manufacturers. It can co-exist in a Z-Wave network existing with product from other
manufacturers.
Hops & Retries
The Z-Wave range has a range of up to 30 meters in line of sight. This signal is not limited
to the 30 meter range due to routing the Z-Wave message to other nodes in the network.
This way the range of the Z-Wave network can be expanded to 150 meters indoors (limit of
4 hops).
Class: 0x20 COMMAND_CLASS_BASIC
When a movement is detected a basic set frame with value 255 is sent to the associated
nodes. If the con gured time is done with no movement is detected a basic set frame with
value 0 is sent to the associated nodes. This is the controlling role of the basic command
class.
The supporting role of the basic command class is mapped to the sensor binary command
class.
Class: 0x25 COMMAND_CLASS_SENSOR_BINARY
The Sensors Binary Command Class can be used to check if motion is detected, value 0
means that there is no motion detected and therefore a associated node is o , value 255
means that a associated node is on.