Cisco 7961G - IP Phone VoIP Руководство по администрированию - Страница 6

Просмотреть онлайн или скачать pdf Руководство по администрированию для IP-телефон Cisco 7961G - IP Phone VoIP. Cisco 7961G - IP Phone VoIP 12 страниц. Unified communications manager 9.0 (sccp and sip)
Также для Cisco 7961G - IP Phone VoIP: Руководство пользователя (21 страниц), Руководство пользователя (25 страниц), Краткая справка (2 страниц), Руководство пользователя (4 страниц), Информационный лист (8 страниц), Руководство пользователя (4 страниц), Руководство пользователя (13 страниц), Руководство пользователя (13 страниц), Руководство по эксплуатации телефона (30 страниц), Руководство пользователя (13 страниц), Руководство (12 страниц), Руководство пользователя (6 страниц), Руководство по администрированию (16 страниц)

Phone Startup Process

The phone displays the Configuring IP message continuously until you either enable autoregistration

or add the phone to the Cisco Unified Communications Manager database.

If the phone has registered previously, the phone accesses the configuration file named

SEPmac_address.cnf.xml, where mac_address is the MAC address of the phone.

For SIP phones, the TFTP server generates these SIP configuration files:

• SIP IP Phone

• Dial Plan: <dialplan>.xml

• Softkey Template: <softkey_template>.xml

The filenames derive from the MAC Address and Description fields in the Phone Configuration window of

Cisco Unified Communications Manager. The MAC address uniquely identifies the phone. For more

information, see the Cisco Unified Communications Manager Administration Guide.

For more information about the phone interaction with the TFTP server, see the Cisco Unified Communications

Manager System Guide, "Cisco TFTP" chapter.

Phone Startup Process

When connecting to the VoIP network, the Cisco Unified IP Phones go through a standard startup process,

described in the following steps. Depending on your specific network configuration, not all of these steps

may occur on your Cisco Unified IP Phone.

Procedure

Step 1

Obtain ower from the switch

If a phone is not using external power, the switch provides in-line power through the Ethernet cable attached

to the phone.

Step 2

Load the stored phone image

The Cisco Unified IP Phone has non-volatile Flash memory in which it stores firmware images and user-defined

preferences. At startup, the phone runs a bootstrap loader that loads a phone image stored in nonvolatile flash.

Using this image, the phone initializes its software and hardware.

Step 3

Configure VLAN

If the Cisco Unified IP Phone is connected to a Cisco Catalyst switch, the switch next informs the phone of

the voice VLAN defined on the switch. The phone needs to know its VLAN membership before it can proceed

with the Dynamic Host Configuration Protocol (DHCP) request for an IP address.

Step 4

Obtain an IP address

If the Cisco Unified IP Phone is using DHCP to obtain an IP address, the phone queries the DHCP server to

obtain one. If your network does not use DHCP, you must assign static IP addresses to each phone locally.

Step 5

Access a TFTP server

Cisco Unified IP Phone 7941G, 7941G-GE, 7942G, 7961G, 7961G-GE, and 7962G Administration Guide for Cisco

Unified Communications Manager 9.0 (SCCP and SIP)

◦ For unsigned and unencrypted files: SEP<mac>.cnf.xml

◦ For signed files: SEP<mac>.cnf.xml.sgn

◦ For signed and encrypted files: SEP<mac>.cnf.xml.enc.sgn

Cisco Unified IP Phones and Your Network