Cisco 1700 series Настройка - Страница 29

Просмотреть онлайн или скачать pdf Настройка для Сетевой маршрутизатор Cisco 1700 series. Cisco 1700 series 34 страницы. Secure firewall management center
Также для Cisco 1700 series: Руководство по нормативному соответствию и безопасности (45 страниц), Руководство (15 страниц), Руководство по конфигурации (25 страниц), Примечание по применению (41 страниц), Поиск и устранение неисправностей оборудования (12 страниц), Обзорное руководство (13 страниц), Руководство (5 страниц), Краткое руководство по эксплуатации (6 страниц), Руководство по установке оборудования (46 страниц)

Печатать страницу

Parallel reads to TCQ:0 tx count reset = 0, periodic safe start = 0

Serial idb(AAL5) output_qcount:0 max:40

Serial idb(RAW) output_qcount:0, max:40

Sar ctrl queue: max depth = 10, current queue depth = 0, drops = 0, urun cnt = 0, total

cnt = 99

Serial idb tx count: AAL5: 0, RAW: 0, Drop count:AAL5: 0, RAW: 0

SCC Clockrates:

WIC

---- ----------- ---------- ----------

FPGA Dev ID (LB)

FPGA Dev ID (UB)

FPGA Revision

WIC

Configuring FRF.5 and FRF.8 Internetworking Functions

To communicate over WANs, end-user stations and the network cloud typically must use the same type

of transmission protocol. This limitation has prevented differing networks such as Frame Relay and ATM

from being linked. The Frame Relay–to–ATM Service Interworking feature allows Frame Relay and

ATM networks to exchange data despite differing network protocols. The functional requirements for

linking Frame Relay and ATM networks are provided by the Frame Relay/ATM PVC Service

Interworking Implementation Agreement specified in Frame Relay Forum (FRF) documents FRF.5 and

FRF.8. The FRF.5 and FRF.8 interworking functions involve multiplexing PVCs between Frame Relay

and ATM networks and mapping the control bits between Frame Relay frame headers and ATM cell

headers. FRF.5 and FRF.8 are necessary for ATM-based features to interwork with Frame Relay–based

IP class of service (CoS) features.

Configuration Examples

These examples show how to configure a mapping between a Frame Relay data-link connection

identifier (DLCI) and an ATM PVC, using the connect command. For a full description of the connect

command as used in the FRF.5 and FRF.8 internetworking functions, refer to Enhanced Voice and QoS

for ADSL and G.SHDSL on Cisco 1700 Series, Cisco 2600 Series, and Cisco 3600 Series Routers.

For FRF.5 and FRF.8, you may need to match the maximum transmission unit (MTU) between the ATM

Note

and Frame Relay networks for large size packets.

FRF.5

The following example shows how to create an FRF.5 connection, using the network-interworking

keyword in the connect command.

interface serial0

no ip address

encapsulation frame-relay IETF

no fair-queue

frame-relay interface-dlci 100 switched

frame-relay intf-type dce

interface atm1

OL-3317-03

SCC-A = 5300000

SCC-B = 4000000

Value

0x44

0x53

0xA1

Config Reg

0x4D

Configuring FRF.5 and FRF.8 Internetworking Functions

Notes

'D'

'S'

WIC / VIC select = WIC;

Configuring an ADSL WAN Interface Card on Cisco 1700 Series Routers