CA.MI NEW ASKIR 118 BASIC Руководство по эксплуатации - Страница 9

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Медицинское оборудование CA.MI NEW ASKIR 118 BASIC. CA.MI NEW ASKIR 118 BASIC 15 страниц.

Печатать страницу

PROXIMITY FUNCTIONS:



Pressing the "Proximity" (Lights BLUE LED) is activated on / off the motor by an infrared proximity sensor that detects the

presence of the operator's hand from a few inches away. This allows the operator to use the device without touching or focus

on pressing the button.



The on / off button is also active with the function of proximity inserted and can be used as an alternative.



To remove the "Proximity" you have to re-press the button.

The "Proximity" is retained, or if it was active before power off, then on again to return to this, but if it was not active will remain

disabled. The function set to power down the card after 20 minutes after turning off the engine if it is not then on again.

The unwanted approach of the hand to the Proximity sensors causes the device to switch off. To reactivate the

function, place the hand close to the sensors.

NOTE: It is up to the end user to activate or deactivate the Proximity sensor. With the Function off, the device is activated/deactivated

by pressing the ON/OFF key.

LIGHT INDICATORS:

The device is provided with a light indicator (directly on the front panel) which allows you to view the operation of the device,

autonomy of the battery, and the charge phase in progress.

The light indications, which appear during operation, are indicated in table I.

TAB. I – INDICATOR LIGHTS DURING OPERATIONS

LED signals

Flashing Green Led

Steady Greed Led

Steady Red Led

Flashing Red Led

Steady Yellow Led

TAB. II – WRITTEN SIGNALS / BUTTON LED SIGNAL

Button LED signal /

written signal

ON/OFF button

Proximity Button

Using FLOVAC® disposable collection system: Before connecting the disposable collection system, remove the blu ring fitted on

the tank holder for a more comfortable insertion of the same container.

After opening the package, fully stretch the bag and then flatten it concentrically to eliminate as much air as possible.

Insert the bag and apply the cover to an appropriately sized reusable rigid container by pressing firmly around the entire

perimeter. Make sure that the system is completely sealed.

close the connector marked as "TANDEM" with the lid provided.

Connect the power source of the vacuum to the VACUUM port equipped with specific reusable conical fitting with "male"

connection.

Connect the patient tube to the PATIENT port of the cover

Before use, check all closures and make sure there are no leaks, starting the aspiration source. If the bag expands to fully

adhere to the walls of the rigid container and the cover bends towards the inside of the glass, the system is not leaking.

Start the aspiration and periodically check the filling level of the container. The overflow valve will cause the interruption of

aspiration if the aspirated fluids have reached the maximum filling level of the device.

When the float valve intervenes signalling the device is too full, the suction source must be disconnected within no more than

5 minutes.

Warning: The accidental inversion of connections may cause contamination for the operator and/or for the vacuum

generation equipment.

Phase

During rechanrge

During recharge

During battery

operation

Device automatically

turns off when the

battery is flat

During battery

operation

Function

Power on

Switch the ON/OFF key

Problem / Cause

Battery recharge running

Recharging cycle complete

Flat battery

Battery completely flat

Intermediate status

Colour

Green / Yellow / Red

Blue

Solution

Wait

Remove the device from the

support plate (ASKIR SUPPORT

118 - mod. ASU 118) of the

ambulance

Start recharging cycle

WARNING: During this signal, you

will hear a long, continuous beep

(duration of sound 0.8 sec / sound

frequency: every 8.5 sec, which

notifies the user regarding the

battery discharge.

When the device is restarted the

LED will flash red: begin the

battery recharge cycle

immediately

Guaranteed battery function /

Recharge when the red LED signal

comes on.

Position

Near the front panel key

LED located above the

"Proximity" key