ACU-RITE 00786 Руководство

Просмотреть онлайн или скачать pdf Руководство для Погодная станция ACU-RITE 00786. ACU-RITE 00786 1 страница. Wireless indoor/outdoor weather station

Печатать страницу

ADDITIONAL FEATURES (continued)

Low Battery Indicator:

Low Battery indication is shown for the home unit itself and all of the remote sensors (up to 3).

When the low battery indicator is displayed, replace the batteries and follow the setup

procedure as shown in this instruction manual.

SPECIFICATIONS:

Range of temperature measurement:

Indoor unit

: 32º F to 122º F (0º C to 50º C), 20% - 99% RH

Remote sensor

: -4º F to 140º F (-20º C to 60º C)

Transmission

: up to 100 feet (30 M) in an open area

Resolution

: 0.1 degree for temperature, 1% for RH

Moon phase

: 8 resolutions

Battery

: 2- "AA" for the main unit, 2 "AAA" for each remote sensor.

Alkaline batteries are recommended.

BUTTON FUNCTIONS:

BUTTON

PRESS BUTTON ONCE

Start or stop radio controlled

SET

time signal search

ALARM

Read alarm time for 5 seconds

Read Maximum / Minimum record

MIN/MAX

for 5 seconds

CHANNEL

Select channel 1 to 3 for viewing

Advance in settings by one step

Turn the alarm on or off

Move back in settings by one step

Switch thermometer reading

between C and F

Activates snooze / backlight (3 sec.)

SNOOZE / LIGHT

STEP TWO: SETTING THE ATOMIC CLOCK

About The Atomic Clock:

The National Institute of Standards and Technology (NIST) in Fort Collins, Colorado broadcasts

the time signal (WWVB at 60kHz AM radio signal) with an accuracy of one second per every

3,000 years. The signal covers a distance of up to 2,000 miles from the source.

Selecting the ideal location:

Like a typical AM radio, the Atomic Clock will not receive the WWVB signal in places

surrounded by heavy concrete or metal panels. For best reception, please install the home

reciever near a window. The time signal reception is also greatly affected by electrical or

electronic interference. If the home receiver location you selected does not work, change to

a location in another part of the room or building.

Radio Controlled Time Reception Set Up:

The clock attempts to synchronize with the Atomic time signal AUTOMATICALLY right after

the first sensor is registered. The unit will start synchronizing the clock after registering the

remote sensor thermometer reading. An antenna icon appears in the upper right hand of the

time section. The clock will not respond to any manual settings while attempting to receive

the Radio Control Time Signal. This reception cycle lasts from 2 to 5 minutes. The antenna

icon remains fixed after the clock is synchronized.

Entering The Time Zone:

After the unit successfully synchronizes withthe atomic time signal, the time zone must be

entered.

• Press & hold "C/F ZONE" button on the back of the home reciever for 3 seconds, press

"C/F ZONE" button to select P/M/C/E time zones. The letters appear in the area where the

seconds are shown in the time display. When you select thecorrect time zone, press the

"SET" button to confirm your choice and exit the selection mode.

P = P acific Standard Time

M = Mountain Standard Time

The clock will not respond to any manual settings while attempting to receive the Radio

Control Time Signal. Press the "SET" button to turn the reception off and to enable manual

settings.

Daylight Saving Time (DST) Feature :

The DST feature is enabled when the batteries are installed. The DST icon appears as a

flashing "D." For areas not using DST in summer, select DST off mode as described under

Step Three: Manually Adjusting Clock & Calendar Setting.

PRESS & HOLD FOR 3 SECONDS

Enter clock & calender set mode

Enter alarm set mode

N/A (no function)

Delete current channel reading

Fast forward through settings

Fast backwards through settings

Time zone selection (P/M/C/E)

N/A (no function)

C = Central Standard Time

E = Eastern Standard Time

STEP ONE: SETTING UP THE WIRELESS THERMOMETER

Home Receiver Set Up:

For the initial installation, always insert batteries in the home unit first, and then the remote

sensor. Remove the battery cover on the back and install 2 "AA" batteries (not included)

according to the polarity indicated. Replace the battery cover.

Remote Sensor Set Up:

Remove the bracket stand and remove the 4 screws with a small phillips head screwdriver.

Insert 2 "AAA" alkaline or lithium batteries (not included) according to the polarity indicated.

Set channel 1 for the first remote sensor. To enable the weather forcastfeature, you must set

to Ch 1 if only one sensor is in use. One sensor is included with the base unit. Additional

sensors may be purchased seperately. Set channel 2 if using a second sensor, or channel 3

if using a third sensor. To purchase additional sensors call 1-800-KLOCKIT and ask for

wireless remote sensor model 00911. You can also order via the web at

www.chaneyinstrument.com. Click on "Where to Find" and then click on the images of the

Acu>Rite weather instruments. Enter 32266 in the search box at the top of the next page.

• To verify transmission of a signal press the "TX" button inside the battery compartment

of the remote sensor. The red LED on the front of the remote sensor will flash when it

successfully transmits a signal. Temperature and humidity of the remote sensor will be

updated and displayed on the remote sensor.

• Select Celsius or Fahrenheit by pressing the "C/F" button inside the battery compartment.

• Replace the cover and tighten the 4 phillips head screws.

STEP THREE: MANUALLY SETTING THE CLOCK & CALENDAR

Press and hold the "SET" button for 3 seconds:

• The setting sequence is:

Year > Month > Date > Hr > Min > 12/24 hr > DST on/off > Weather Offset > EXIT Settings

• Press the "+" or "-" buttons on the back of the Receiver to set each function to the correct

setting. Once the display is showing the correct setting, press the "SET" button to confirm

your settings and to advance to the next function.

• The corresponding digits will be flashing during the setting procedure.

• After completing the setting sequences pressing the "SET" button will return the display to

the standard view.

ADDITIONAL FEATURES

Setting the Alarm:

Press and hold the "ALARM" button for 3 seconds.

• The display will show the alarm set time and the letters "AL" appear to the right of the

minute digits. The hour digits will be flashing.

• Press the "+" or "-" buttons on the back of the case to set the hours to your desired time.

Please be sure to note that the AM/PM idicator is set properly. Press the "ALARM" button to

confirm the hour setting and to proceed to the minute setting.

• The minute digits will be flashing. Press the "+" or "-" buttons to set the minutes to the

desired setting.

• Press the "ALARM" button again to exit the setting procedure.

To stop the alarm, press any button when the alarm sounds. This will automatically reset the

alarm to sound agian the next day at the same time. To turn off the alarm completely, press

the "+" button on the back of the case. To turn the alarm back on for use, press the "+" again.

Snooze / Light:

Press the "snooze/Light" button to activate the 8 minute snooze alarm. Each press will also

activate the green backlight which will remain illuminated for 3 seconds before turning itself

off to conserve the batteries.

MIN / MAX Memory:

Press the "MIN/MAX" button to view the maximum indoor and outdoor temperature and

indoor humidity values for 5 seconds. Press again to view the minimum values. The min/max

memory will automatically clear every day at midnight.

Temperature Trend:

Small arrow icons displayed in boxes will indicate: Rising, Steady, Falling. Refresh rate for the

outdoor temperature trend is once every hour.

Moon Phase:

Moon Phase is shown by the scrolling of the moon icon from left to right. The icon will stop at

the existing moon phase for 5 seconds, and then resume scrolling.

00786 Wireless Indoor/outdoor Weather Station

C/F

Remote

Home Receiver

Sensor

Bracket

Stand