Digitalk SP808 Руководство пользователя - Страница 4
Просмотреть онлайн или скачать pdf Руководство пользователя для Сотовый телефон Digitalk SP808. Digitalk SP808 4 страницы. Digitalk communicator
Печатать страницуCOMMUNICATOR MODEL SP808
BABY-SITTER and PARENT-MONITOR Function
Setting BABY Unit On/Off
1. Press the MENU
button 5 times to enter Baby Unit selection page.
2. Press
/
button to toggle the Baby unit ON or OFF. ( If the System
has been set to become a Monitor Unit, Baby unit cannot be enabled).
3. Press Enter
or PTT button to confirm and the BUTTON LOCK is on
during Baby-Sitter mode.
4. When the System is set as a Baby unit, VOX function would be also
enabled. It allows transmission without pressing the PTT button. But
receiver function would be disabled.
5. Press & Hold the Enter
function.
Setting Monitor Unit On/Off
1. Press the MENU
button 6 times to enter Monitor Unit selecting page.
2. Press
/
button to toggle the Monitor unit ON or OFF. (If the System
has been set to become a Baby Unit, Monitor unit cannot be enabled).
Press Enter
or PTT button to confirm.
3. When the System is set as a Monitor unit, transmiittor function would
be disabled.
4. Press the MENU
button 6 times again to turn OFF the MONITOR
function.
Internal VOX Control Function
On VOX mode, automatically transmitting and receiving signals without
pressing any button.
To turn on the VOX function:
1. Press MENU
button 8 times to enter the VOX mode;
2. While the VOX icon (OFF 1-4) is flashing;
= Press Up
button to select higher VOX sensitivity (OFF 1-4);
= Press Down
buttons to select lower VOX sensitivity (OFF 1-4);
= The most sensitivity level is 4.
3. Press ENTER
or PTT button to confirm the selected mode.
To turn off the VOX function:
1. While the VOX icon (OFF 1-4) is flashing, press Up
and to select the "OF" mode.
2. Press ENTER
button to confirm the VOX off mode.
To activate the VOX sensitivity:
1. While the VOX mode is on, plug the connector of the headset (not
included) into SP ./MIC jack of the communicator and then speak
through the microphone of the headset to activate the transmitting
mode.
2. Transmitting mode will turn on automatically and on standby mode.
3. The TX LED indicator illuminates red when transmitting.
NOTE: 1. The VOX sensitivity is automatically activated once plug the
connector of the Headset (not included) into SP ./MIC jack of
the communicator. You don't have to push the PTT button of the
communicator while transmitting.
2. While VOX mode is on. Pressing ENTER
VOX transmission for 4 seconds.
Battery Level Indicator:
1. The BATTERY LEVEL is indicated by the number of squares present inside
the BATTERY icon on the LCD Screen.
2. When the BATTERY LEVEL is low, a BEEP tone will continue in every 15
seconds to alert the batteries are in low voltage and need to be
replaced.
Repeater Function
Press
button one time to enter REPEATER mode, press
more time to release REPEATER function. During REPEATER on mode,
display will show REP icon.
button again to deactivate the Baby Sitter
or Down
button can suspend
To Charge The COMMUNICATOR
The units must be used with orignal Charger Pod and AC -DC Adpator
(optional).
* AC -DC Adpator: input 240 VAC 50Hz - Output 6V DC 200mA.
1. Turn the unit OFF (Do not turn ON the unit during Battery Charge Mode).
2. Install 3.6V "AAA" Ni-MH Rechargeable Battery Pack into the battery
compartment of unit.
3. Connect the lead of the AC-DC adapter to the socket at the back
of the charger pod (make sure the lead has been fully inserted into
the jack with some force). Connect the AC-DC adapter to the mains
power supply.
4. Place the unit into the Charger Base.
5. The LED light on the Charger Base will turn RED once electricity get
connected.
6. Unplug the Adpator. Turn the unit ON. The Battery Level Indicator on
the LCD Screen will display the new Battery Level.
NOTE: 1. LED Indicator on the charger base will NOT turn OFF automatically,
except take out the unit from the charger base and disconnect
the electricity.
2. It takes approximately 6 hours to fully charge the batteries if they
are at their lowest level or takes around 14 hours to fully charge
the new batteries.
WARNING: DO NOT attempt to charge any type of regular Alkaline
button
button one
batteries in this unit. Only use the orignal AC-DC Adaptor with
the supplied battery pack (optional) or AAA Ni-MH
rechargeable batteries.