Digitalk 2 - WAY COMMUNICATOR Руководство пользователя и инструкция по эксплуатации - Страница 3

Просмотреть онлайн или скачать pdf Руководство пользователя и инструкция по эксплуатации для Двухстороннее радио Digitalk 2 - WAY COMMUNICATOR. Digitalk 2 - WAY COMMUNICATOR 5 страниц.

Печатать страницу

Getting Started

LCD Screen:

Battery Indicator

Channel Number

Duplex Icon

REP

Dual Watch

Button Lock

Displayed during CHANNEL SCAN mode.

SCAN

Press and hold the ENTER

until the BUTTON LOCK symbol is displayed.

Displayed when receiving a signal.

BUSY

Channel Number changes from 1 to 40

as selected by user.

Displays current BATTERY LEVEL.

Displays current VOLUME LEVEL.

Displayed during DUAL WATCH mode.

Displayed during VOX mode is on.

VOX

Displayed during Duplex mode is on.

REP

Operation

Changing Channels:

The COMMUNICATOR has 40 available channels. To change channels:

1. Press the MENU

button until the current channel number flashes

on the LCD Screen.

2. While the channel number is flashing:

Press the Up s button to move to a higher channel.

Press the Down t button to move to a lower channel.

The channel changes from 1 to 40, or from 40 to 1.

3. Press the ENTER

button to confirm the selected channel and

return to the NORMAL mode.

4. Channel change operations are disabled during BUTTON LOCK mode.

NOTE: Refer to the "Channel Table" section of this Owner's Manual for

detailed frequency listings.

Monitor:

You can use the MONITOR feature to check for weak signals in the

current channel.

1. Press the MONITOR M button.

2. Press and hold the MONITOR M button unit it "beeps" for continuous

monitoring.

ENTER / Back-light / Button Lock:

1. Press and immediately release the ENTER

LCD Screen. The BACKLIGHT will automatically shut off after 4 seconds

if no other buttons have been pressed.

2. Press and hold the ENTER

displayed on the LCD Screen.

NOTE: Volume and Channel Change Operations as well as Call &

Monitor Operations are disabled during BUTTON LOCK mode.

Press and hold the ENTER

BUTTON LOCK mode.

RX Icon

Channel

Scan

Selection

BUSY

SCAN

VOX

Volume Level

button

button to light up the

button until the BUTTON LOCK icon is

button again to deactivate

Getting Started

Turning the Unit ON:

Press and hold the

button. The unit will "beep" with dual tone and the

LCD SCREEN will briefly display a SELF-TEST Screen.

Turning the Unit OFF:

Press and hold the

button. The unit will "beep" with a signal tone and

the LCD Screen will turn blank.

Adjusting Speaker Volume:

1. Press the Up s button to increase the Speaker Volume.

2. Press the Down t button to decrease the Speaker Volume.

3. The Speaker Volume level is indicated by the number of bars displayed

in the lower right corner of the LCD Screen.

NOTE: Volume Up s and Down t buttons are disabled during BUTTON

LOCK mode

Receiving a Signal:

The unit is continuously in the RECEIVE mode when the unit is ON and not

Transmitting. When you receive a signal on the current channel, the RX

icon (BUSY) is displayed. (See "LCD SCREEN" for details).

Transmitting a Signal:

1. Check the channel activity by pressing and holding the MONITOR M

button. You'll hear static if the channel is unoccupied. Don't TRANSMIT

if someone is talking on the channel. Press and hold the PTT button to

TRANSMIT. The TX LED Indicator will light up in red. Hold the unit in a

vertical position with the MICROPHONE 2 to 3 inches from the mouth.

2. While holding the PTT button, speak into the unit using a normal tone

of voice.

3. Release the PTT button when you have finished transmitting.

NOTE: In order for other people to receive your transmission, they must

also be on the same channel you are currently using. Refer to the

"Changing Channels" section for more information.

Operation

Channel Scan:

CHANNEL SCAN performs searches for active signals in an endless loop

from 1 to 40.

1. Press MENU

button twice and Up s , Down t buttons to activate

CHANNEL SCAN. The channel number on the LCD Screen changes

rapidly until an active signal is detected.

During CHANNEL SCAN mode.

Press ENTER

button or PTT button to confirm the selected channel.

Press the CALL C button to change to CALL function and to send

a CALL TONE on that active channel.

Press the MENU

button 4 times to deactivate CHANNEL SCAN

mode.

2. When an active signal (one of 40 channels) is detected. CHANNEL

SCAN pauses keeping the active signal broadcasted.

3. Press the PTT button to communicate through the active signal channel

and CHANNEL SCAN is deactivated.

4. When an active signal (one of 40 channels) is detected, but another

channel is desired, press the MONITOR M button 2 times to bypass the

current channel and continue to search for another active channel.

Sending Call Tones

You can use CALL TONES to alert the other when you are attempting to

contact them. You can also use CALL TONES to signal the beginning or

the end of a transmission.

1. Press the CALL C button, the red TX LED indicator will light up and the

CALL TONE continues for 3 seconds.

2. Release the CALL C button, your CALL TONES will transmit to nearby

receivers set to the same channel.