Consumable Replacement Messages
When you see the following messages in the LCD screen or in
the EPSON Status Monitor 3 window, you need to replace
the indicated unit. You can continue printing for a short time
after a message appears, but Epson recommends replacement
to maintain print quality and extend the life of your product.
LCD screen message
Description
Worn Photoconductor
The photoconductor is near the end of its
service life. Replace the photoconductor with
a new one.
Worn Fuser
The fuser has reached the end of its service
life.
Worn uuuu Dev Unit
The developer has reached the end of its
service life.
Note:
To clear the message, press the
panel, select Reset from Printer settings, then select Clear All
Warnings.
The CX11N stops printing if the worn consumable might damage the
CX11N. You must replace the consumable product to continue.
If a consumable product reaches the end of its service life, the
product stops printing and displays the following messages on
the LCD screen or in the EPSON Status Monitor 3 window.
LCD screen message
Description
1
Replace Toner uuuu
The indicated toner cartridge is empty.
2
Replace Photocondctr
The photoconductor is at the end of its
service life.
1 The letters C, M, Y, and K appear in this position, indicating the
color of the empty toner cartridge.
2 Even if this message is displayed in the LCD screen, you can
continue to print for a short time by pressing the
x
Color Start button on the control panel. The message in the
LCD screen changes from Replace Photocondctr to Worn
Photoconductor.
Messages appear for one consumable product at a time. After
replacing a part, check the LCD screen for replacement
messages for other parts.
Replacing a Toner Cartridge
When a toner cartridge is empty, a message appears on the
LCD screen indicating which toner cartridge needs to be
replaced. If you are going to print a large document or make a
large number of copies and one of the toner cartridges is low,
you can change that cartridge so you won't run out of toner in
the middle of the job. See:
❏ "Changing a Low Toner Cartridge" (next column)
❏ "Removing and Replacing a Toner Cartridge" on page 12
Setup button on the control
x
B&W Start or
Epson AcuLaser CX11N/CX11NF
Handling Precautions
Always follow these precautions when replacing a toner
cartridge:
❏ Install a genuine Epson toner cartridge. Using a non-Epson
toner cartridge may affect print quality. Other products
may cause damage to your printer not covered by Epson's
warranty.
❏ When handling toner cartridges, always place them on a
clean smooth surface.
❏ If you move a toner cartridge from a cool to a warm
environment, wait for at least one hour before installing it
to prevent damage from condensation.
Warning:
Do not touch the toner and keep it away from your eyes. If toner gets
on your skin or clothes, wash it off with soap and water immediately.
❏
Keep toner cartridges out of the reach of children.
❏
Do not dispose of toner cartridges in fire, as they may explode
and cause injury. Dispose of them according to local
regulations.
❏
If toner spills, use a broom and dustpan or a damp cloth with
soap and water to clean it up. Because the fine particles can
cause a fire or explosion if they come into contact with a
spark, do not use a vacuum cleaner.
Changing a Low Toner Cartridge
1. Make sure the CX11N is turned on, then press the
button.
Setup
The Setup light turns on and the LCD screen displays
for a few seconds, then changes to the Setup
Setup Mode
menu screen.
2. Use the u or d button to select
press the r button.
3. Use the u or d button to select
r button.
4. Use the u or d button to select
for the color of the toner cartridge you want to change, then
press the r button.
5. Continue with the steps in the next section to remove and
replace the toner cartridge.
8/05
Epson AcuLaser CX11N/CX11NF
, then
Printer Settings
, then press the
Reset Menu
Change Toner C/M/Y/K
11
-
Печатать страницу