Argo Argoclima Magico Руководство по эксплуатации - Страница 6

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Кондиционер Argo Argoclima Magico. Argo Argoclima Magico 10 страниц. Movable air conditioner

Печатать страницу

HOW TO SET THE PRESENT TIME

Press the SET button for five seconds. The time indication

alone flashes.

Press the + or - buttons until the present time is displayed.

Press the SET button to stop the indication flashing.

COOLING

NOTE

Verify that the unit is connected to the main

power and the STANDBY lamp is light up.

1. Set the MODE selector to COOL

2. Press the ON/OFF button and switch the

air conditioner ON.

3. Press the TEMP. buttons to set the

desired temperature (the temperature

range is between 30 °C max. and 16 °C

min.).

THE DISPLAY SHOWS THE

SELECTED TEMPERATURE.

4. Press the FAN SPEED button to select the fan speed.

NOTE

The air conditioner disposes of the condensate water automati-

cally at the HIGH and MEDIUM fan speed, on the contrary at

the LOW fan speed the condensate water is collected in the

tank.

DEHUMIDIFYING (DRY)

Set the MODE selector switch to "DRY"

2. Press the ON/OFF button and switch the air conditioner ON.

3. Press the TEMP. buttons to set the room temperature (the

temperature range is between 30 °C max. and 16 °C min.).

THE DISPLAY SHOWS THE ROOM

TEMPERATURE.

NOTE

Use DRY operation when you want to reduce the humidity

in the room.

During DRY operation, the fan speed is automatically set to

low or stops to prevent overcooling.

Dry operation is not possible if the indoor temperature

is 15 °C or less.

The humidity of the room (condensate water) will be collected

in the internal tank of the air conditioner.

FAN ONLY

If you want to make air circulate without any temperature

control, follow these steps:

1. Set the MODE selector switch to "FAN"

2. Press the ON/OFF button and switch the air conditioner

ON.

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN SPEED selector to the

A microcomputer automatically controls the fan speed when the

AUTO mode is selected. When the air conditioner starts

operating, the difference between the room temperature and

the set temperature is detected by the microcomputer which

then automatically switches the fan speed to the most suitable

level.

In FAN Only mode the fan speed is adjusted automatically

as in cooling mode.

WHEN DIFFERENCE BETWEEN

ROOM TEMPERATURE AND SET

Cooling and

dehumidifying

modes:

The above mentioned data make reference to air conditioner

operating when the sensor on the remote control unit is ON.

(Refer to temperature sensor selector). If the sensor on the unit

is being used then actual operation will slightly differ from that

described in the above tables.

MANUAL

If you want to manually adjust speed just set the FAN SPEED

selector as desired.

SLEEP MODE

The SLEEP mode enables you to save energy.

1. Set the MODE selector to cool or dry.

2. Press the SLEEP button.

3. The

button again to release the SLEEP function.

What does the SLEEP mode mean?

In this mode, the air conditioner will cool or dry the room to the

set temperature, and then the thermostat will make the unit

pause. After about 1 hour, the air conditioner will automatically

reset the set temperature as follows (also refer to graph).

When the room temperature reaches the new set value, the

thermostat will cause the unit to pause. After about 1 hour the

temperature will be raised by 1°C. This enables you to save

energy without sacrificing your comfort.

NOTE

TEMPERATURE IS

2 °C and over

Between 2 and 1 °C

Below 1 °C

NOTE

High speed

Med. speed

mark appears on the display. Press the SLEEP

COOLING AND DEHUMIDIFYING

Setting temperature

1°C

1 hour

position.

FAN SPEED

High

Medium

Low

Low speed

Room temperature

TIME