Sony BRU-SF10 Руководство по эксплуатации - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Видеокамера Sony BRU-SF10. Sony BRU-SF10 40 страниц. Hd optical multiplex unit
Также для Sony BRU-SF10: Технический паспорт (22 страниц)
Печатать страницу
D ALARM indicator
Lit red: Check for the following.
• The BRU-SF10 is not properly connected to
the camera via optical fiber cable. Check the
connections, and restart the unit.
• Image frequency settings for the camera and
the BRU-SF10 are different. Check the
settings after turning off the power, and then
restart the unit.
• The camera may be unable to start properly
due to the AC adapter being improperly
connected to the DC IN connector on the
camera. Check that the camera is turned on.
• An unsupported optional interface card is
inserted in the card slot of the BRU-SF10.
Remove the card after turning off the power,
and then restart the unit.
Off: The unit is in normal operation.
E SD indicator
This indicator lights when a BRBK-SA1 optional
interface card is installed, or when a BRBK-HSD2
is installed and its rear switch is set to SD.
F Camera ID indicators
The number for the current camera address lights
orange.
For details on setting the camera address, see
"Q VISCA FUNCTION switches" on page 7.
G Status indicators
The current communication format, baud rate, and
video format settings light green.
For details on configuring these settings, see
"Q VISCA FUNCTION switches" on page 7.
H DATA MIX switch
When the SD indicator is lit, set this switch to ON
to overlap the menu display with the SD image
signals from any installed BRBK-SA1 and
BRBK-HSD2 interface cards on which the rear
switch is set to SD.
Set this switch to OFF to hide the menu display.
Rear
9
0 qa
IN
OUT
EXT SYNC
CAMERA
6
GB
Location and Function of Parts
qs qd qf
qg
qh
IN
OUT
1 2 3 4 5 6 7 8 9
RGB/COMPONENT
VISCA RS232C
VISCA RS422
AUDIO OUT
L
FUNCTION
1
R
10
DC 12V
ql
qk
qj
I CAMERA connector
Connect to the optical connector of the BRBK-SF1
HD Optical Multiplex Card installed in the
BRC-Z330 camera using the CCFC-S200 Optical
Fiber Cable.
A dustproof cap is attached at the factory.
Do not remove this cap if you do not intend to
connect an optical fiber cable. Dustproof caps are
also attached to the BRBK-SF1 and CCFC-S200.
Do not remove these caps when the connectors are
not in use.
J EXT SYNC IN connector
Accepts external video sync signals.
K EXT SYNC OUT connector
Supplies external video sync signals input from the
EXT SYNC IN connector.
When a cable is connected to this connector, the
75-ohm termination for inputs is automatically
opened, and signals input to the EXT SYNC IN
connector are output from this connector.
L
RGB/COMPONENT connector
Supplies the images from the camera as YPbPr or
RGB signal.
M VISCA RS-232C IN connector
Connect to the RM-BR300 Remote Control Unit
(not supplied). When you connect multiple
cameras, connect it to the VISCA RS-232C OUT
connector of the previous camera in the daisy chain
connection.
N VISCA RS-232C OUT connector
When you connect multiple cameras, connect it to
the VISCA RS-232C IN connector of the next
camera in the daisy chain connection.
CAUTION
When you connect the RS-232C connecting cable
of the unit to peripheral device, use the supplied
cable to prevent malfunction due to radiation noise.
O VISCA RS-422 connector
Connect to the VISCA RS-422 connector of the
camera or another BRU-SF10 HD Optical
Multiplex Unit.
For the connection to the VISCA RS-422
connector, see "Using the VISCA RS-422
Connector Plug" on page 12.