Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Примечание по установке - Страница 28

Просмотреть онлайн или скачать pdf Примечание по установке для Сетевое оборудование Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 36 страниц. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Также для Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Примечание по установке (14 страниц), Руководство по решению (17 страниц), Примечание по установке (46 страниц), Белая книга (19 страниц), Описание (1 страниц), Бюллетень продукции (6 страниц), Уведомление (4 страниц), Информационный лист (9 страниц), Информационный лист (18 страниц), Белая книга (18 страниц), Руководство по конфигурации (8 страниц), Примечание по установке (28 страниц), Руководство по устранению неполадок (11 страниц), Примечание по установке (18 страниц), Руководство пользователя (17 страниц), Примечание по установке (24 страниц), Руководство (19 страниц)

Removing and Installing Ethernet Modules in the Chassis

If you have upgraded a WS-X6748-GE-TX Ethernet module that was equipped with a stiffener bracket,

Caution

verify that you did not reinstall the stiffener bracket on the module. The bracket can be discarded.

Reinstall the Ethernet module in the chassis.

Step 7

If you are unsure about the correct procedure for installing an Ethernet module in the switch chassis,

refer to the

installation instructions.

Removing and Installing Ethernet Modules in the Chassis

This section describes how to correctly remove and install an Ethernet module in a Catalyst 6500 series

switch chassis slot.

The WS-X68xx and the WS-X69xx Ethernet modules require that adjacent slots (above and below or to

Note

the left and to the right) that are empty have switching-module filler plates (Cisco part numbers

WS-X6K-SLOT-CVR-E or SLOTBLANK-09). If either unused slot currently has a blank slot cover

(Cisco part number WS-X6K-SLOT-CVR) installed, you must remove the blank slot cover and replace

it with a switching-module filler plate for NEBS compliance.

During this procedure, wear grounding wrist straps to avoid ESD damage to the card.

Caution

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into

beams or view directly with optical instruments. Statement 272

Removing an Ethernet Module from the Chassis

To remove an Ethernet module from the chassis, perform these steps:

Disconnect any network interface cables attached to the Ethernet module.

Step 1

Attach an ESD grounding strap to your wrist and to a proper ground.

Step 2

Verify that the captive installation screws on all of the modules in the chassis are tight. This step ensures

Step 3

that the space created by the removed module is maintained.

Note

Loosen the two captive installation screws on the Ethernet module.

Step 4

Catalyst 6500 Series Distributed Forwarding Card 4 for WS-X68xx, WS-X69xx, and Select WS-X67xx Modules Installation Note

"Removing and Installing Ethernet Modules in the Chassis" section on page 28

If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on

the installed modules expand and push the modules toward the open slot, which reduces the

opening size and makes it difficult to reinstall the module.

for

OL-24918-02