Sony PXW-FS7 Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Цифровая камера Sony PXW-FS7. Sony PXW-FS7 28 страниц. Getting s-log output
Также для Sony PXW-FS7: Руководство по обновлению (13 страниц), Руководство (36 страниц), Руководство по эксплуатации (1 страниц), Руководство (2 страниц), Руководство (10 страниц)

Печатать страницу

English

This document describes the added/changed

features of the camcorder introduced by

firmware version 1.10, and provides

amendments to the Operating Instructions

manual. Read the following instructions

together with the Operating Instructions (PDF

format), stored on the accompanying CD-ROM,

and the printed documents.

S-Log2 signal settings added (Ver.1.10)

S-Log2 is a log signal that has a dynamic range of

1300% that also takes into account visibility on a

video monitor, with color grading performed in

post processing.

S-Log2 settings have been added to each of the

following setup menu functions.

• S-Log2 added to Gamma >Gamma Category

in the Paint menu

When Gamma Category is set to S-Log2,

Gamma Select is also set to S-Log2.

• P4: S-Log2 added to Monitor LUT >LUT

Select in the Video menu

Selectable only when Base Setting >Color

Space in the System menu is set to S-Gamut/

SLog2. Color Space switches to S-Gamut.

• Added S-Gamut/SLog2 to Base Setting

>Color Space in the System menu

Video Signal Monitor limitations (Ver.1.10)

• To use Video Signal Monitor, SDI output must

be enabled. Also, the output resolution must be

2K or lower. Check the following settings.

- Output On/Off >SDI in the Video menu

- Output Format >SDI in the Video menu

• In the following cases, Video Signal Monitor

cannot be displayed in the viewfinder.

- When the SDI output is edge cropped using

Output Setting >4K/2K to HD Conv. in the

Video menu

- When there is a mixture of MLUT On and

MLUT Off settings for Monitor LUT >SDI1

& Internal Rec, SDI2, HDMI, and Viewfinder

in the Video menu

Output Format default value changed (Ver.1.10)

The default value for Output Format in the Video

menu has been changed to 1920×1080 or

2048×1080.

Notes

• Always set the POWER switch to the Off position

before detaching or attaching a battery pack or AC

adaptor. If it is detached or attached with the POWER

switch in the On position, the camcorder may be

unable to start in some cases.

If the camcorder cannot be started, set the POWER

switch to the Off position and remove the battery pack

or AC adaptor temporarily, then wait about 30 seconds

before attempting to attach again. (If the AC adaptor is

detached or attached while the camcorder is operating

from the battery pack, or vice versa, it can be detached

or attached with the POWER switch in the On position

without problem.)

• When recording to media in both XQD card slots A

and B, insert media in both slots that is recommended

for operation with the format to record.

• If the record button is pressed within a few seconds

after turning the camcorder on, the recording indicator

lights up to indicate the unit is in the recording state,

but recording to media may not occur for the first few

seconds, depending on the selected recording format.

Note when using a Wireless LAN Connection

In the current version, the unit supports video

monitoring only (when using the CBK-WA100).

Please replace the description provided on page 47

in "Connecting Devices using Wireless LAN" as

described above.

Attaching to a tripod

Use the tripod screw holes on the camcorder

when attaching to a tripod. Using the tripod

mount on the lens may cause damage.

Protecting the connector terminals

Attach the cover to unused connectors to protect

the connector terminals.

Rec Button Set

When the record START/STOP button and the

handle record START/STOP button are set to

control recording for different memory cards,

SDI/HDMI Rec Control and RAW Rec Control

follow the recording state of slot A.

When creating a LUT using RAW Viewer

Select F55/F5 as the output format when creating

a LUT using RAW Viewer.

Create and deploy LUT files in the following

folder on an SD card.

\PRIVATE\SONY\PRO\CAMERA\

PMWF55_F5