Digitrax SDH104K1A Руководство пользователя - Страница 5
Просмотреть онлайн или скачать pdf Руководство пользователя для Медиаконвертер Digitrax SDH104K1A. Digitrax SDH104K1A 12 страниц. Plug n’ play mobile decoder with soundfx
Печатать страницу
shipped with CV01 (AD2), the two digit address, set to 03. Following is a brief
description of how to change the decoder address with a Digitrax DT series
throttle. See your Starter Set Manual for complete programming instructions.
1. Place the loco on the programming track or on the main line.
2. Enter the programming mode using your DCC system/throttle. On DT400
press PROG until you see "Pd" if using a programming track or "Po" if
using the main line.
3. Use your throttle to choose the address you want to set up for the decoder.
On the DT400 use the left knob to dial AD2 for two digit programming, use
the right knob to dial up the address, click the right knob to change to AD4
for programming 4 digit addresses.
4. Complete address programming. On DT400 press ENTER. Note: CV29
must also be programmed to enable 4 digit addressing, this is done automat-
ically by the DT300 & DT400 but not on earlier throttles.
U U s s i i n n g g t t h h i i s s d d e e c c o o d d e e r r i i n n o o t t h h e e r r l l o o c c o o m m o o t t i i v v e e s s
The sound project loaded into this decoder is for an AC4400 diesel locomotive.
If you want to install it in a different locomotive, you can simply load a dif-
ferent sound project for that type of locomotive. The cam input is available
for steam installations where you want to synchronize chuffing.
D D i i g g i i t t r r a a x x L L o o c c o o M M o o t t i i o o n n
Your locomotives look like the real thing, now you can make them run like the
real thing, too. Digitrax decoders incorporate torque compensation for smooth
as silk operation. You can also program CVs that control momentum, 3 step
and 128 step speed tables, switching speed, normal direction of travel,
scaleable speed stabilization and more to take full advantage of the Digitrax
LocoMotion System.
M M o o m m e e n n t t u u m m - - C C V V 0 0 3 3 & & C C V V 0 0 4 4
Momentum is part of the LocoMotion System. Acceleration is controlled by
CV03 and deceleration by CV04. Both come from the factory set to 000/x00. A
range of 000/x00 to 031/x1F is available for both accel and decel. We recom-
mend that you try CV03:003/x03 and CV04:000/x00 as a starting point for
experimenting with momentum.
S S p p e e e e d d T T a a b b l l e e s s - - H H o o w w t t h h e e L L o o c c o o R R e e s s p p o o n n d d s s t t o o t t h h e e T T h h r r o o t t t t l l e e
With Digitrax LocoMotion, there are two types of speed tables: 3 Step Tables
and High Resolution 28 Step Tables. Please see your Digitrax Decoder Manual
for a discussion of the 28 Step Tables. The 3 Step Tables are set up by program-
ming 3 CVs: Start Voltage (CV02), Mid point Voltage (CV06) and Max Voltage
(CV05). These values are set at 000/x00 at the factory. All have a range of val-
©2006 Digitrax, Inc
2 2 4 4 4 4 3 3 T T r r a a n n s s m m i i t t t t e e r r R R D D
P P a a n n a a m m a a C C i i t t y y , , F F l l 3 3 2 2 4 4 0 0 4 4
w w w w w w . . d d i i g g i i t t r r a a x x . . c c o o m m
S S y y s s t t e e m m
®
www.digitrax.com
8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 8 8 9 9 0 0
T T
8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 5 5 5 5 7 7
F F
s s a a l l e e s s @ @ d d i i g g i i t t r r a a x x . . c c o o m m
E E
5