Cisco AT&T 3G MicroCell Руководство пользователя - Страница 19
Просмотреть онлайн или скачать pdf Руководство пользователя для Шлюз Cisco AT&T 3G MicroCell. Cisco AT&T 3G MicroCell 20 страниц. Wireless signal booster
Также для Cisco AT&T 3G MicroCell: Руководство пользователя (20 страниц), Руководство по началу работы (11 страниц), Краткое руководство по эксплуатации (8 страниц)
Печатать страницу
FCC Compliance
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against such interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If not installed
and used in accordance with the instructions, it may cause harmful interference to
radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorientorrelocatethereceivingantenna,ifapplicable.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich
the receiver is connected.
• Consulttheserviceprovideroranexperiencedradio/televisiontechnicianfor
help.
Any changes or modifications not expressly approved by Cisco Systems, Inc., could
void the user's authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below
is a requirement of the FCC and is intended to supply you with information
regarding the FCC approval of this device. The phone numbers listed are for FCC-
related questions only and not intended for questions regarding the connection
or operation for this device. Please contact your service provider for any
questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions: 1) the device may not cause harmful interference, and
2) the device must accept any interference received, including interference that
may cause undesired operation.
AT&T 3G MicroCell™
Model: MicroCell
Manufactured by: Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
This device complies with RSS-132 and RSS-133 of the Industry Canada Rules.
Operation is subject to the following two conditions:
• Thisdevicemaynotcauseharmfulinterference.
• Thisdevicemustacceptanyinterferencereceived,includinginterferencethat
may cause undesired operation.
Software and Firmware Use
The software (including firmware) described in this document is protected by copyright
law and furnished to you under a license agreement. You may only use or copy this
software in accordance with the terms of your license agreement.
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may appear
in this guide. We reserve the right to change this guide at any time without notice.
Radiation Exposure Statements
Note: This transmitter must not be collocated or operated in conjunction with any
other antenna or transmitter. This equipment should be installed and operated with
a minimum distance of 7.9 inches (20 cm) between the radiator and your body.
United States
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This system has been evaluated for RF exposure for
humans in reference to ANSI C 95.1 (American National Standards Institute) limits.
The evaluation was based on evaluation per ANI C 95.1 and FCC OET Bulletin 65C
rev 01.01. The minimum separation distance from the antenna/radiator to a general
bystander is 7.9 inches (20 cm) to maintain compliance.
This transmitter must not be collocated or operating in conjunction with any other
antenna or transmitter.
The availability of some specific channels and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match
the intended destination. The firmware setting is not accessible by the end user.
Canada
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This system has been evaluated for RF exposure for
humans in reference to ANSI C 95.1 limits. The evaluation was based on evaluation
per RSS-102 Rev 2. The minimum separation distance from the antenna to general
bystander is 7.9 inches (20 cm) to maintain compliance.
20081121 FCC Standard
19