Acuity Brands nLiGHT rMSOD Краткое руководство по эксплуатации
Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Аксессуары Acuity Brands nLiGHT rMSOD. Acuity Brands nLiGHT rMSOD 3 страницы. Fixture embedded smart sensor, 360 coverage, low voltage, wireless
Печатать страницу
SPECIFICATIONS (rMSOD)
Electrical Specifications
Mechanical
Environmental
Warrantied Operating Temperature
Contains FCC ID: 2ADCB-RMODIT or 2ADCB-RES7CD
Contains IC: 6715C-RMODIT or 6715C-RES7CD
IFT #: RCPACRM18-1879 or RCPACRE21-0154
Acuity Brands Lighting Inc. RMODIT or RES7CD
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the
radiator shall not be less than 20cm during normal operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the separation between the equipment and receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4.
Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box
and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service should be performed by a qualified licensed electrician.
• Maintenance should be performed by qualified person(s) familiar with the products' construction & operation & any hazards involved. Regular maintenance programs recommended.
• DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly
should be replaced.
CAUTION: RISK OF PRODUCT DAMAGE
√ Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be
worn during all installation or servicing of the unit.
√ Do not touch individual electrical components, as this can cause ESD and affect product performance.
√ Do not stretch or use cable sets that are too short or are of insufficient length.
√ Do not tamper with contacts.
√ Do not modify the product.
√ Do not change or alter internal wiring or installation circuitry.
√ Do not use product for anything other than its intended use.
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com © 2019-2021 Acuity Brands Lighting, Inc. All rights reserved. Rev. 04/29/2021
IS-RMSOD-002
rMSOD Sensor
Fixture Embedded Smart Sensor
360° COVERAGE
LOW VOLTAGE
•
Input Ratings
5 - 60 VDC
Maximum Load
0.65W
Dimming Load
Sinks <20mA (0-10 VDC LED Drivers/Ballasts)
Minimum Load
None
Class Rating
Class 2
Mounting
Fixture-Mounted
Mounting Height
Up to 40 ft (12.192m)
Connection Type
Low Voltage Leads
-40º to 185º F (-40º to 85º C)
Standards/ Ratings
RoHS, UL 916, UL 924 (optional), FCC / IC / IFETEL
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
C
US LISTED
TITLE 20/24
WIRELESS
•
Full warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Actual performance may differ as a result of end-user environment and application.
WARNING - RISK OF ELECTRIC SHOCK
√ Disconnect or turn off power before installation or servicing.
√ Verify that supply voltage is correct by comparing it with the
product information.
√ Make all electrical and grounded connections in accordance with
the National Electrical Code (NEC) and any applicable local code
requirements.
√ All wiring connections should be capped with UL approved
recognized wire connectors.
√ All unused connector openings must be capped.
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
INCLUDING THE FOLLOWING:
• DO NOT MOUNT NEAR GAS OR ELECTRIC HEATERS.
• EQUIPMENT SHOULD BE MOUNTED IN
LOCATIONS AND AT HEIGHTS WHERE IT WILL NOT
READILY BE SUBJECTED TO TAMPERING BY
UNAUTHORIZED PERSONNEL.
• THE USE OF ACCESSORY EQUIPMENT NOT
RECOMMENDED BY THE MANUFACTURER MAY
CAUSE AN UNSAFE CONDITION.
5-year limited warranty.
Note: Specifications subject to change without notice.
WARNING - RISK OF BURN or FIRE
√ Do not exceed maximum wattage, ratings, or published
operation conditions of product.
√ Do not overload.
√ Follow all manufacturer's warnings, recommendations
and restrictions to ensure proper operation of product.
CAUTION - RISK OF INJURY
√ Wear gloves and safety glasses at all times when
installing, servicing or performing maintenance.
WARRANTY
1 of 3