Crow SH-SIRINT-8F Руководство по эксплуатации
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Датчики безопасности Crow SH-SIRINT-8F. Crow SH-SIRINT-8F 2 страницы. Wireless indoor sounder
Также для Crow SH-SIRINT-8F: Руководство по эксплуатации (2 страниц), Руководство (2 страниц)
Печатать страницуSH-SIRINT-8F/9F
WIRELESS
INDOOR SOUNDER
INSTRUCTION MANUAL
P/N 7105411 REV. C
WALL MOUNTING
Figure 2
Use supplied screw to mount the bracket on the wall
Check that the base is flat against the wall to facilitate the unit
device insertion into the wall
bracket
1.
Slide down the unit device
into the bracket
2.
Reset tamper alarm on
the control panel
PRODUCT FEATURES
The SH-SIRINT is an advanced slim designed wireless
indoor sounder that extends the sound of your alarm inside
your premises.
The SH-SIRINT is ideal for residential and light commercial
buildings, particularly where outdoor sirens are prohibited.
• ISM Radio 2GFSK
• Ultra Low current consumption
• Powered by 2 Lithium batteries Type AA 1.5V
• Wall Tamper protection
• Battery life up to 5 years
•
Operating Frequencies: 868-869MHz / 916-917MHz
• Event Transmission:
•
Alarm
Tamper Open/Close
•
Supervision
•
•
Battery status
• Bi-Color LED indications
• Up to 500m transmission range in open space
• Remotely configurable
• Selectable Dipswitches for working with panel types :
Shepherd, Serenity, Runner.
BATTERIES INSERTION
Figure 3
Batteries can be replaced by the user
Please refer to section "Battery Replacement" for this
operation.
PRODUCT OVERVIEW
DIPSWITCHS
Dipswitch Setting
Dipswitch
Shepherd
Serenity/Runner
Number
1
OFF -
ON
Serenity / Runner
2
N/A
ON
ARM
Battery
2
ok
Flashes
Low
3+3
battery
flashes
3
N/A
ON
ARM
Battery
2
ok
Beeps
Low
3+3
battery
Beeps
4
N/A
ON
Flasher and Buzzer timeout is 15 min
dipswitch is OFF timeout is 2 min.
The table describes the different settings for
SHEPHERD, SERENITY, RUNNER panel types.
Note (for Shepherd default): The Alert sound time is 3
minutes and The Alert flasher time is 30 minutes.
Activation time can be changed from Outputs level (see
installation manual)
Note:
Any change in the DIP switches requires
battery removal and reinsert
DEVICE OPENING
Figure 1
1. Push the latch located on the bracket
2. Slide Up the unit device
PAIRING PROCESS
For pairing process, please refer to your control panel
instructions.
To pair your sounder(for Shepherd panel),please proceed
as follows:
DISARM
1.
Enter in installing mode via the" installer Webpage"..
1
2. Go to Outputs and select the output # you want to learn.
flashes
3. Add Output – (insert link type "ISM" Device's ID, Device
2
type "smart siren".
Flashes
4. Set Siren Configuration output, and save configuration.
DISARM
5. Place the 2 batteries as instructed in figure 3 and wait
1 Beep
until the red/green LED stops blinking.
6. The device should register to the Control Panel.
2 Beep
7. When registration process is successfully completed,
the Green LED will constantly light ON for 3 seconds and
then turn OFF.
8.
If Green LED continues flashing more than 5 minutes
and stopped. Please check siren settings details,
remove batteries and repeat step 5,6,7.
Pairing sounder for SERENITY/RUNNER panels
1.
Enter in installing program mode
2.
Go to panel learning mode, and press the enter key
to start the learning process,
3.
Place the battery as instructed in figure 4.
4.
the FW2-NEPTUNE RED/Green LED alternately
blinks and wait until sounder power up and learning
process end.
5.
When registration process is successfully
completed, the Green LED will constantly light ON
for 3 seconds and then turn OFF.
If Registration failed, the Red LED will blink, remove the
battery, wait few seconds, and repeat the learning process.