Epson TM-L90 series Информационный справочник - Страница 4

Просмотреть онлайн или скачать pdf Информационный справочник для Аксессуары для принтеров Epson TM-L90 series. Epson TM-L90 series 5 страниц. Attaching cover on the power switch
Также для Epson TM-L90 series: Брошюра (1 страниц), Брошюра (2 страниц), Руководство по эксплуатации (27 страниц), Технические характеристики (2 страниц), Технические характеристики (8 страниц), Технические характеристики (4 страниц), Руководство пользователя (40 страниц), Руководство пользователя (17 страниц), Руководство пользователя (21 страниц), Руководство пользователя (21 страниц), Руководство по производству (22 страниц), Начните здесь (2 страниц), Начните здесь (2 страниц), Руководство (13 страниц), Руководство по эксплуатации (12 страниц), Руководство пользователя (36 страниц), Руководство по разработке (34 страниц), Руководство (2 страниц)

Печатать страницу
Epson TM-L90 series Информационный справочник
2. Insert the paper roll spacer so that the front edge goes into
the notch and down to the shaft, as shown below.
3. Push the paper roll spacer until you feel it click onto the
shaft.
1RWH &KHFN WKDW WKH SDSHU UROO VSDFHU VOLGHV OHIW DQG ULJKW VPRRWKO\
4. Slide the paper roll spacer to the appropriate width, as
shown above. You can use the measurement printed inside
the printer. Align the inside edge of the spacer with the
desired measurement.
5. Insert the screw included with the spacer into the hole
indicated above and tighten it. (Even if you can see two
holes, this is the only one to put the screw in.)
6. Follow the instructions in this guide to set the memory
switch for the desired paper width.

Testing the Printer

Follow these steps to run a self-test:
1. Load the paper roll and close the paper roll cover.
)(('
2. Hold down the
When printing starts, release the
settings are printed.
3$3(5 287
3. The
light starts to flash when the status has
been printed. Press the
4. After the printer prints the lines for the self-test, it prints
"
*** completed ***
data as soon as it completes the self-test.
1RWH 7R SDXVH WKH VHOIWHVW PDQXDOO\ SUHVV WKH )((' EXWWRQ 3UHVV
)((' DJDLQ WR FRQWLQXH WKH VHOIWHVW
button, and turn on the printer.
)(('
button. The printer
)(('
button to start the test.
." The printer is ready to receive

Removing Jammed Paper

&$87,21 ❑ 'R QRW WRXFK WKH WKHUPDO KHDG RU UDGLDWLRQ SODWH
❑ 'R QRW OHW PHWDO REMHFWV FRPH LQWR FRQWDFW ZLWK
1. Power off the unit, open the paper roll cover, and remove
the jammed paper.
2. If you cannot open the paper roll cover, paper is jammed in
the autocutter. Follow the steps under "Clearing the
Autocutter" below.
Clearing the Autocutter
1. Lift up and remove the cutter cover by inserting a flathead
screwdriver into the slots on each side of the main case and
spreading the case in the direction of the arrows.
2. Rotate the autocutter knob in the direction of the arrow to
return the cutter blade to the normal position. (A triangle
mark shows through the window in the autocutter frame.)
3. Open the paper roll cover, re-install the cutter cover, and
close the paper roll cover.

DIP Switches

Serial interface
%DQN
)XQFWLRQ
1/02
EPSON TM-L90
EHFDXVH WKH\ FDQ EH YHU\ KRW DIWHU SULQWLQJ
WKH WKHUPDO KHDG 0HWDO FDQ GDPDJH WKH KHDG
21
EPSON TM-L90 - 3
2))