Epson TM-L90 series Руководство - Страница 8

Просмотреть онлайн или скачать pdf Руководство для Аксессуары для принтеров Epson TM-L90 series. Epson TM-L90 series 13 страниц. Attaching cover on the power switch
Также для Epson TM-L90 series: Брошюра (1 страниц), Брошюра (2 страниц), Руководство по эксплуатации (27 страниц), Технические характеристики (2 страниц), Технические характеристики (8 страниц), Информационный справочник (5 страниц), Технические характеристики (4 страниц), Руководство пользователя (40 страниц), Руководство пользователя (17 страниц), Руководство пользователя (21 страниц), Руководство пользователя (21 страниц), Руководство по производству (22 страниц), Начните здесь (2 страниц), Начните здесь (2 страниц), Руководство по эксплуатации (12 страниц), Руководство пользователя (36 страниц), Руководство по разработке (34 страниц), Руководство (2 страниц)

Печатать страницу
Epson TM-L90 series Руководство
How to connect an Epson POS printer with Ethernet Interface
Power down the unit
Set Dip-Switch 1 to OFF
Resume operations
Type III
Configuration of Ethernet Type III Module
Epson's "low-cost" Connect-It Ethernet Interface used a manual configuration scheme and and no web interface. The
Type III module can be identified by the red or blue 4 position DIP switch visible on the front of the adapter
An Epson Type III Ethernet Interface Adapter
DIP Normal Switch Settings for the Ethernet III Module (front panel)
DS-1 Off ('On' is used to generate a configuration report)
DS-2 N/A
DS-3 N/A
DS-4 N/A
Jumper Settings (in strip together on circuit board)
JP-1 baud
JP-2 baud
JP-3 DHCP (default: on)
JP-4 factory use (normally off)
Baud rate settings (set using combination of jumper 1 and jumper 2, above)
9600
baud: JP1-Off, JP-2-Off
19200
baud: JP1-On, JP-2-Off
38400
baud: JP1-Off, JP-2-On
Note: The Ethernet III module only supports 9600, 19200 and 38400 baud rates.
The printer and the Ethernet III module must have the same baud rates to communicate.
Get the initial settings of the Printer
Run the printer self test (hold down the feed button while turning on the printer). The printer will print a list of initial settings
including interface type and buffer capacity. Verify that the interface is "serial" for this type of Ethernet adapter and that
the baud rate is the same as is set on the card. If necessary, change the baud rate on the printer (using the
or the baud rate on the module (using jumpers), so they agree.
Get the initial settings of the Ethernet Adapter Card
Turn off power on printer. Change the dip switch 1 to ON. Turn printer on. The printer will print a list of including MAC
address, current IP address and DIP switch and jumper settings.
Note: if you want to enable DHCP for this card, you must place a jumper on JP3. JP3 is located on the circuit board near
the large black connector. DHCP stands for Dynamic Host Configuration Protocol, a network service that automatically
assigns IP addresses to devices.

Installation Steps

1. Disconnect power and other cables from the EPSON printer, and remove the printer DIP switch cover plate.
2. Remove the existing interface board from the printer by unscrewing 2 screws.
3. Properly align and push the new module into the printer. Fasten the two mounting screws through the faceplate of the
new interface.
http://www.beaglehardware.com/howtoethernet.html[3/4/2011 12:27:20 PM]
(Type II or Type III)
Printer
Sale!
DIP
switches)
TM-U220
$129
TM-U295
$184
TM-U375
$199
TM-
U675
$199
TM-
H6000III
$349
TM-T88II
$109