Epson 755c - PowerLite XGA LCD Projector Руководство по эксплуатации - Страница 16

Печатать страницу

Epson 755c - PowerLite XGA LCD Projector Руководство по эксплуатации

Epson PowerLite 755c/765c Projector

Note:

If you don't see your network adapter's IP address, allow a

minute for it to appear. If your access point or AirPort base

station uses DHCP, sometimes it takes a minute for the server to

pick up the IP address.

Once you've selected the IP address for your network adapter,

you won't see the Switch network dialog box when you start

NS Connection. If you want to change to a different network

adapter, click

Extension

box, then click

Switch LAN

You see the screen below. (If you have previously started

NS Connection, this is the first screen you see.)

If the connection is working properly, you see your projector

listed. If you have additional Epson projectors on the

network, they are also listed, along with their status. The

color of the status icon next to each projector's name

indicates its status:

Gray: the projector is not connected

Orange: the projector is connected to another computer

Green: the projector is connected to your computer

Note:

If a projector is in use and is "locked," you won't be able to

select it.

3. If you don't see your projector, check the following:

Make sure your wireless signal is strong enough to

establish a connection. If you have a Macintosh, check

the AirPort icon on the Macintosh menu bar. For

Windows, see the documentation for your access point or

computer network card.

Epson PowerLite 755c/765c Projector

on the EMP NS Connection dialog

Make sure you're trying to connect to the right network.

In Windows, verify that you've enabled your computer's

connection to the access point or that your wireless card

or adapter is enabled, and that its SSID matches the

projector's ESSID. In Macintosh, check the AirPort

status menu (click the AirPort icon on your menu bar) to

make sure AirPort is turned on and the projector's ESSID

or your AirPort network is selected. Remember that the

ESSID is case-sensitive.

Make sure you aren't projecting one of the EasyMP

configuration screens. (You should see a message that the

projector is ready to connect.) If you have to exit the

configuration screen, restart NS Connection.

Make sure the ESSID for your projector matches the

SSID for your wireless card, adapter, or access point. If

you have an AirPort base station, make sure the

projector's ESSID matches the AirPort network name.

Remember that the ESSID is case-sensitive.

Note:

The AirPort network name may be different than the

AirPort base station name. To check the network name, start

the AirPort Admin utility, select your base station, and click

. Then click

Configure

name appears on the AirPort tab.

Check the IP address for both your projector and your

wireless card, adapter, access point, or AirPort base

station. The first three sections of the IP address should

be identical. The last section of the projector's IP address

should be close, but not identical, to the last section of

the IP address for your wireless interface, access point, or

base station.

Restart your computer and start NS Connection again.

If you still don't see your projector and you are using

access point mode, follow the instructions in

"Connecting in IP Connect Mode" on page 17 to

connect to the projector manually.

Make sure you have disabled any firewall software.

4. Once the name of your projector appears, select it and click

. If more than one projector is listed, you can select

Connect

up to four additional projectors and connect to them at the

same time. If the selected projector is being used by another

person, you can still connect to it; doing so automatically

disconnects the other user.

5. If you are prompted for a keyword, enter the four-digit

number displayed on the EasyMP Network screen and

click

8/05

. The network

Show All Settings