Epson Perfection 600 Информация о продукте - Страница 4
Просмотреть онлайн или скачать pdf Информация о продукте для Программное обеспечение Epson Perfection 600. Epson Perfection 600 5 страниц. Technical brief (scanners)
Также для Epson Perfection 600: Руководство (11 страниц)
Печатать страницу
EPSON Perfection 600
If your system doesn't recognize the scanner
or the SCSI board (PC only)...
Check the plug-and-play option.
If you're running Windows 95, plug-and-play should be
active.
If you're running Windows NT, plug-and-play should be
disabled. (You can disable ISA plug-and-play from the
Advanced Configuration Options menu in SCSISelect.)
If you're running Windows 3.1, run SCSISelect to disable
plug-and-play.
Did you install another SCSI device, such as a ZIP drive, after
you installed your SCSI board? (Windows 95 only)
If so, your device installation may have overwritten the SCSI
driver (sparrow.mpd) with an older version of the driver.
Copy sparrow.mpd from the Sparrow directory on your
EPSON CD-ROM to the \windows\system\iosubsys
subdirectory on your hard drive.
Run the Add New Hardware wizard.
(Windows 95 and NT only)
Follow the instructions on the screen. (It's best to accept the
default settings.) When you're done, restart your computer.
Run SCSISelect.
Your scanner comes with the 1505 SCSISelect diskette, which
contains SCSISelect, a special SCSI troubleshooting and
configuration utility for Windows 3.1, Windows 95, and
Windows NT. Insert this diskette in your diskette drive and
restart your computer, then follow the instructions on your
screen.
If SCSISelect hangs or you get an error message, you have a
hardware problem. Make sure your SCSI board is installed
correctly. If the SCSI card is found, but not the scanner, you
need to install a SCSI terminator. Also, check the SCSI cable
connection and make sure the scanner is turned on. After
checking your hardware, run SCSISelect again.
If you continue to have problems, your SCSI board may be
defective.
If the scanner doesn't scan your image.
Check your image source setting.
Make sure you selected the Perfection 600 as your source.
Run the scanner test (PC only).
Run the scanner test to make sure the scanner is
communicating with your computer. If the test fails, check the
items above. (The scanner test is not available for the
Macintosh.)
4 - EPSON Perfection 600
Check the cable connecting the scanner to the computer.
Make sure the scanner is correctly connected to the computer.
Also, make sure the scanner's ready light is on.
Check the terminator and SCSI ID.
Make sure you've attached the terminator and set the correct
SCSI ID.
If the scanner software doesn't work
properly...
Check your system requirements.
Check that the system requirements, such as the operating
system version, are correct for your software.
Check your computer's memory.
See if the computer has enough memory for your software. If
you're running other software at the same time, using RAM
resident programs, or have many device drivers, the computer
may not have enough memory. (See your software and
computer manuals.)
Check your software installation.
Make sure that your software is correctly installed or set up. If
all else fails, uninstall your software, then reinstall it.
If the file size is too big...
Adjust your scan settings.
Try setting a lower resolution, or scan only part of the image.
If your scanned image is blurred or distorted...
Check the position and condition of your document.
Make sure the document is placed flat against the scanner's
document table (the glass area). If only part of the image is
blurred, part of your document may be wrinkled or warped.
If your scanned image is faint or has gaps...
Check the brightness.
Decrease the scanner driver's brightness setting.
Check the condition of your original.
If the document is damaged, dirty, or wrinkled, these
imperfections will show up in your scan.
If your image scans at an angle...
Check the position of your source document.
It may be placed at an angle on the document table. Align it so
the horizontal and vertical edges are carefully aligned with the
scales on the top and side of the document table.
9/97