Dimplex BLF34 Руководство по эксплуатации - Страница 13
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Крытый камин Dimplex BLF34. Dimplex BLF34 16 страниц. Fireplace
Печатать страницуwedged underneath the Partially Reflective Glass. They
may obstruct the ease of removing the Partially Reflective
Glass from the fireplace.
2. Remove the Partially Reflective Glass retaining brack-
ets by removing the 2 screws on each brackets; (2
brackets in total), located on the left and right side of
the Partially Reflective Glass. (Figure 14)
3. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
4. Slide the controls assembly out toward the front of the
unit.
CAUTION: Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
5. Remove the Partially Reflective Glass. Carefully place
the glass assembly aside in a safe location.
6. Remove the heating cover by removing the 4 screws: 2
on the left and 2 on the right of the tray. (Figure 14)
7. Locate the high temperature cutout and remove the
mounting screw.
8. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
9. Slide the controls assembly out toward the front of the
unit.
CAUTION: Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
10. Disconnect the wiring connections noting their original
locations.
!
NOTE: Using a flat head screwdriver gently pry between
the end of the connectors and the board to release the
wires.
11. Properly orient the new high temperature cutout and
connect all of the wiring connections.
12. Reassemble in the reverse order as above.
ELEMENT REPLACEMENT
WARNING: Disconnect power before attempting any
Figure 14
Cover
Panel
Blower
Assembly
Heating
Elements
Cutout
Heating
Cover
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required: Phillips head screwdriver.
Needle nosed pliers.
CAUTION: Follow "Preparation for Service" instructions
before proceeding.
1. Remove the decorative glass ember-bed pieces from
the media tray, which lies along the bottom of the interi-
or Partially Reflective Glass. A medium sized container
such as a bucket or a box will be needed to keep the
glass ember-bed pieces together.
!
NOTE: Try to ensure the pieces do not get pushed or
wedged underneath the Partially Reflective Glass. They
may obstruct the ease of removing the Partially Reflective
Glass from the fireplace.
2. Remove the Partially Reflective Glass retaining brack-
ets by removing the 2 screws on each brackets; (2
brackets in total), located on the left and right side of
the Partially Reflective Glass. (Figure 14)
3. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
4. Slide the controls assembly out toward the front of the
unit.
CAUTION: Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
5. Remove the Partially Reflective Glass. Carefully place
the glass assembly aside in a safe location.
6. Remove the heating cover by removing the 4 screws: 2
on the left and 2 on the right of the tray. (Figure 14)
7. From the top panel of the heating assembly housing,
remove the 4 screws that hold the element cover to the
housing panel.
8. Disconnect wires from the ends of the elements noting
their original locations.
!
NOTE: Using a flat head screwdriver gently pry between
the end of the connectors and the element to release the
wires.
!
NOTE: Some of the wires may have a "piggy-back"
connector that allows a second wire to connect to the same
prong as the first wire. Try and keep the "piggy-back" con-
nection together when pulling the wires off the element.
9. Reassemble in the reverse order as above.
CAUTION: When re-installing covers and panels, be
sure the wires are guided and tucked into the proper open-
ings along the right side so they are not pinched and allows
enough space to reinstall panel.
BLOWER/FAN REPLACEMENT
WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
13