Philips AZ-2040 Руководство пользователя - Страница 6
Просмотреть онлайн или скачать pdf Руководство пользователя для Стереосистема Philips AZ-2040. Philips AZ-2040 12 страниц. Cd soundmachine
Также для Philips AZ-2040: Руководство пользователя (9 страниц), Руководство пользователя (15 страниц), Руководство (8 страниц), Руководство по эксплуатации (34 страниц), Руководство (10 страниц), (шведский) Snabbmanual (8 страниц)
Печатать страницу
BASIC FUNCTIONS
Batteries (not included)
• Insert 6 batteries, type R-20, UM-1 or D-cells,
(preferably alkaline) with the correct polarity.
Remote control (for AZ2045 only /See A)
• Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline).
Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Mains
1 Check if the mains supply, as shown on the type
plate located on the bottom of the set,
corresponds to your local mains supply. If it does
not, consult your dealer or service centre.
2 If your set is equipped with a voltage selector,
adjust the selector so that it matches with the
local mains.
3 Connect the mains lead to the wall socket.
4 To disconnect the mains supply, unplug the set
from the wall socket.
Auto-Standby mode
When a CD or tape has reached the end of playback
and remains in the stop position for more than
15 minutes, the set will switch off automatically to
save mains.
The type plate is located on the bottom of the
set.
BASIC FUNCTIONS
Switching on and off and selecting function
1 Press y on the set to switch on.
2 Press SOURCE once or more to select:
or
function.
TAPE
3 Press y to switch off the set.
Notes:
– To change from
when you are switching off the set: first, make
sure you press the tape STOP 9 key to end
playback and all the cassette keys are released.
– The tone, sound settings, tuner presets and the
volume level (up to a maximum volume level of 20)
will be retained in the set's memory.
Adjusting volume and sound
1 Adjust the volume with the VOLUME control.
™ Display shows the volume level and a number
from 0-32. (See 2)
2 Press DBB once or more to select dynamic bass
boost on or off.
™ Display: shows
3 To adjust the bass, mid and treble tones, press and
hold + or – on the BASS, MID, HIGH keys until
you reach the desired level, –5 to +5
™ Display briefly shows
level. (See 3)
Note: To prevent sound interference the bass control
options operate exclusively. You cannot combine the
bass from BASS with DBB
™ The display shows
automatically switched off to remind you if you
attempt to use both bass settings
Mute (for AZ2045 only)
1 Press MUTE on the remote control to interrupt
sound reproduction instantly.
™ Playback continues without sound and the
display flashes
2 To reactivate sound reproduction you can:
– press MUTE again;
– adjust the volume controls;
– change source.
DIGITAL TUNER
Tuning to radio stations
1 Press y to on, then press SOURCE to select
.
TUNER
–
is displayed briefly and then the radio station
TU
frequency, waveband and, if programmed, a
,
CD
TUNER
preset number are shown. (See 4)
2 Press BAND once or more to select your
waveband.
DIGITAL TUNER
to
or
function, or
TAPE
TUNER
CD
when activated.
,
, or
BASS
MID
HIGH
or the
.
and the
indicator is