Philips AZ1826 Руководство пользователя - Страница 5

Просмотреть онлайн или скачать pdf Руководство пользователя для Стереосистема Philips AZ1826. Philips AZ1826 13 страниц. Cd soundmachine
Также для Philips AZ1826: Технический паспорт (2 страниц), Руководство по быстрому использованию (2 страниц), Руководство по быстрому использованию (1 страниц), Руководство по быстрому использованию (2 страниц)

Печатать страницу

POWER SUPPLY/BASIC FUNCTIONS

Batteries contain chemical substances, so

they should be disposed of properly.

Using AC Mains

1 Check if the mains supply, as shown on the type

plate located on the bottom of the set,

corresponds to your local mains supply. If it does

not, consult your dealer or service centre.

2 Connect the power cord to the AC MAINS ~ inlet

and the wall socket. The set is now ready for use.

3 To switch the set off completely, withdraw the

power cord from the wall socket.

4 Install the unit near the AC outlet and where the

AC power plug can be easily reached.

• Disconnect the power cord from the wall socket to

protect your set during heavy thunderstorms.

Children could seriously injure themselves as the

free end of the cable may still be live if only the

connector is removed from the MAINS socket at

the back of the unit.

The type plate is located on the bottom of the

set.

IMPORTANT!

For users in the U.K.: please follow the

instructions on the lower left hand-side.

Helpful hints:

– To avoid unnecessary energy consumption, always

adjust the Source selector to OFF after using

the set.

BASIC FUNCTIONS

Switching on and off and selecting function

1 To switch on, adjust the Source selector to

CD/USB, MW or FM as desired.

• To switch between CD and USB mode, first adjust

Source selector to CD/USB position, then press

CD/USB button once or more.

2 To switch off, adjust the Source selector to OFF.

Adjusting volume and sound

1. Adjust the volume with the VOL 3, 4 or DBB ( on

the remote control).

™ Display shows

number from 00-32.

DIGITAL TUNER

Tuning to radio stations

1 Push the source selector to MW or FM.

– The radio station frequency, waveband and a

preset number (if programmed) are shown.

(See 2)

and the volume level in

2 Press and hold ∞ or § ( TUNING + - on the

remote control) until the frequency in the display

starts running.

™ The radio automatically tunes to a station of

sufficient reception. Display shows

during automatic tuning.

3 Repeat step 2 if necessary until you find the

desired station.

• To tune to a weak station, press ∞ or §

( TUNING + - on the remote control) briefly and

repeatedly until you have found optimal reception.

To improve radio reception:

• For FM, extend, incline and turn the telescopic

aerial. Reduce its length if the signal is too strong.

• For MW, the set uses a built-in aerial. Direct this

aerial by turning the whole set.

Programming radio stations

You can store up to a total of 20 radio stations in the

memory (20 FM and 20 MW), manually or

automatically (Autostore).

Manual programming

1 Tune to your desired station (see Tuning to radio

stations).

2 Press PROG to activate programming.

™ Display: PROG flashes.

3 Press -, + ( PRESET

once or more to allocate a number from 1 to 20.

4 Press PROG to confirm.

5 Repeat steps 1-4 to store other stations.

Helpful hints: You can erase a preset station by

storing another frequency in its place.

Autostore

Autostore automatically starts programming radio

stations from preset 1. Any previous presets e.g.

manually programmed will be erased.

1 Select MW or FM.

2 Press and hold PROG until

™ Available stations are programmed (MW or FM).

After all stations are stored, the last autostore

preset station will then automatically play.

To listen to a preset or autostore station

Press the ALBUM/PRESET -, + (on the remote

–

control PRESET

) buttons once or more until the

desired preset station is displayed.

This set complies with the radio interference

requirements of the European Union.

DIGITAL TUNER

–

on the remote control)

displays.