Toshiba TDP-EW25 Руководство пользователя - Страница 23

Просмотреть онлайн или скачать pdf Руководство пользователя для Проектор Toshiba TDP-EW25. Toshiba TDP-EW25 50 страниц. Extreme short throw projector
Также для Toshiba TDP-EW25: Технические характеристики (2 страниц), Руководство по установке (6 страниц)

Toshiba TDP-EW25 Руководство пользователя
Using the menus 1 (Continued)
Default setting 2 menu
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
Fan mode
Sets the cooling fan speed.
Remote control When projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[
or
: Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Key lock
Lock the control panel buttons.
[
or
: Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Lamp power
Set the lamp power.
Reset all
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password setting
p.35
Password
Press
.
Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from types. You can set each code respectively for up to
projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
Description
p.23
(Rear)
(Ceiling)
Standard
[
]
[
: Confirm]
: Select from 1, 2
]
[
: Select On/Off
]
[
: Confirm]
]
Low
Standard
Yes
p.18 p.19
44
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
(Rear ceiling)
with the control panel buttons is disabled.
To release the key lock, set the [Key lock] to [Off] using remote control. Pressing
High
the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the indicators of LAMP and TEMP light in orange
for seconds, and at the same time the projector beeps.) However, when Network
or USB memory input is selected, the [Key lock] cannot be set to [Off] with the
[RETURN] button on the projector.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.
No
Item
Input
Mode name
Resolution
Frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count The count for lamp replacement
Total time
Version
Notes
1:
The mode of supported RGB signals
:
Sync signal polarity shown as P (positive) or N (negative) for [H/V].
Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot
:
be used as a counter of guaranteed lamp time.) When the displayed time approaches
,000 hours, consult with a dealer about getting replacement for:
TLPLW15 for TDP-EW5 (sold separately).
4:
[Version] shows the version of the projector's internal control program. This version
is referred to for customer service, etc.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Description
Computer Y/P
Input source name
Yes
[Note 1]
RGB input mode
Yes
Resolution (in dots)
Yes
Sync frequency
Yes
Sync signal polarity
[Note ]
Yes
Y/P
/P
signal format
No
B
R
Color method of video signal
No
[Note ]
Time of lamp use
Yes
Yes
The total time that this projector is
Yes
used.
[Note 4]
Firmware version
Yes
is shown.
p.94
45
"Yes": displayed, "No": not displayed
USB
/P
Video S-video Network
B
R
memory
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes