Dimplex AC3CN Руководство пользователя - Страница 3

Просмотреть онлайн или скачать pdf Руководство пользователя для Нагреватель Dimplex AC3CN. Dimplex AC3CN 4 страницы. Recessed ceiling heater/ over door heater
Также для Dimplex AC3CN: Инструкции (4 страниц), Руководство пользователя (8 страниц)

Печатать страницу

Installation of Switch Panel

WARNING: The Switch Panel should not be installed in a toilet or

washroom.

The backing box (standard B.S. double gang as shown in Fig. 5) should

be rebated into a suitable wall. The box should be ﬁ tted so that the switch

panel will be ﬂ ush with the wall. Suitable wall conduit should be used where

applicable to carry the cable between the heater and the switch panel.

Installation of Heater

The Installation of this product must only be carried out by a prescribed

competent person in accordance with Building Regulations and the current

IEE Wiring Regulations for electrical equipment.

This heater can either be installed into a suspended or plasterboard ceiling.

First it is necessary to ensure that 200mm of sufﬁ cient space exists above

the ceiling for the Installation of this product (see Fig. 1 and Fig. 7).

This product is designed to be suspended by threaded rod or wires/chains.

Always ensure this unit is adequately supported when installed.

Mounting of Heater

Installation in a plasterboard (or similar) Ceiling

A hole (610x610mm) as indicated in Fig. 1 and Fig. 6 must be cut into the ceiling.

It may be necessary to ﬁ x an internal supporting frame around the newly cut

aperture in a plasterboard ceiling.

see Fig. 11

To mount the unit into the ceiling void, use lengths of threaded bar or hooks

(not supplied) screwed into the M8 threaded inserts located in the top side

of the heater (see Fig. 1 for dimensions). Adjust the height of the heater so

the air inlet/outlet panel is positioned inside the grille frame and no more than

70mm above the installed height of the egg crate grille which allows access

for future maintenance. The unit should also be positioned inside the grille

400

Access Panel

265

Doorway

Fig. 7

2 3

120

145

opening to achieve optimum air-ﬂ ow

effect, as shown in Fig. 8.

Installation in a Bulk Head

(over doorway)

A hole (576x265mm) as indicated in

Fig. 7, must be cut into the ceiling part

of the bulk head. Drop rods should

be used to mount the appliance in

such a position, as to have the base

flush with the ceiling. An access

panel should also be provided on the

front of the bulkhead. This provides

access to the top of the appliance

and the access plate for wiring the

appliance.

70mm max.

max.

4 4 0mm min.

min.

Installation in a Suspended Ceiling

A standard 600 x 600mm ceiling tile needs to be removed as close to

the ﬁ nal position of the product as possible.

There are four options for mounting the appliance in a suspended ceiling:

Use suitable length M8 threaded bar and screw into the threaded inserts

provided on the top of the heater - see Fig. 1 for dimensions.

Bend up the 'Wire Hooks' as shown in Fig. 9 and use suitable suspended

Fig. 5

ceiling wire to suspend the heater. (Note the appliance should be mounted

as to prevent swaying of the product during operation).

Without Egg Crate Grill: Use the rail brackets provided. Bend the rail

brackets as shown in Fig. 10. The appliance should be placed directly

onto the suspended ceiling structure in the desired location. Using the

screws provided screw the rail brackets onto the heater (Top Holes -

see Fig. 9) so that it grips the suspended frame (see Fig. 10) Close the

remaining space around the heater with a cut ceiling tile.

Fig. 6

With Egg Crate Grill: Use the rail brackets and ceiling tile provided.

Pick a location to mount the heater. Remove the existing ceiling tile

and replace with metal tile supplied. The appliance should be placed

directly onto the metal ceiling tile. Using the screws provided screw the

rail brackets onto the heater (Bottom Holes - see Fig. 9) so that it grips

the suspended frame (see Fig. 10).

Note: Please ensure that the ceiling structure can withstand the weight of

the appliance.

Operation of Switch Panel

Switch on electrical supply (MAINS IN) to the Switch Panel.

Switching the switch marked 'I' (see '1' in Fig. 5) energises the fan and

switches on the electrical supply to the heater.

The heat selection switches allow heat settings to be chosen as shown

below:

Settings - I

The desired setting can be obtained through switch selection.

Fan Only

I +

Heat

I +

Full Heat

200mm

200

min.

Fig. 8

TOP HOLES : WITHOUT TILE

BOTTOM HOLES : WITH TILE

Fig. 9

Fig. 10