AEO E-power 5A 1S Инструкции - Страница 2
Просмотреть онлайн или скачать pdf Инструкции для Двигатель AEO E-power 5A 1S. AEO E-power 5A 1S 2 страницы. Brushless motor esc
Introduction
1.All devices are original and genuine, ensuring that the ESC is of the highest quality and high
reliability.
2. It can withstand a higher current.
3. It can set the throttle stroke, compatible with a variety of remote control .With smooth and
delicate feel of speed control,first-class linear speed regulation.
4. The maximum speed can be reached 210,000 RPM (2-pole motor), 70,000 RPM (6-pole motor)
and 35,000 RPM (12-pole motor).
•Thank you for purchasing this product. It is strongly recommended that you read
this manual carefully before using the device and strictly comply with the specified
operating procedures. We are not responsible for any liability arising from the use
of this product.
Note: This manual is not suitable for E-power 5A (1S/2S)
Function
1. The type of battery: Lithium battery / NI-MH battery
2. Battery low voltage protection mode: limit the throttle to only 40% when the voltage reaches low voltage protection.
3. Advance angle: divided into low, medium and high.
In general, the low advance Angle can accommodate more motors. However, as the motor structure is quite different, please try each advance
Angle to get a satisfactory driving effect. In order to improve the speed, the advance Angle can be set as the high advance Angle. After
changing the approach Angle, it is recommended to test on the ground before flying.
Setting Instruction
Using your brushless ESC for the first time
Please pay attention! In order to adapt the ESC to your remote control throttle stroke, the throttle stroke should be resetting for the first time when using this ESC
or changing other remote controls, so as to get the best linear throttle.
Setting instructions of throttle stroke
Turn on the
remote
control,then adjust
the throttle to the
highest point.
The lowest voice
"♫123" from ESC
indicates the
throttle to be the
lowest.
Instruction of Normal Boot
Turn on the remote
control,then adjust
the throttle to the
lowest point.
Programming instructions for using the remote control
Turn on the remote
control,then adjust
the throttle to the
highest point.
After hearing a certain
function sound, pull
down the throttle and
♫45
sound "
" to select
this function.
The highest voice
Connect the ESC to
"bi-bi" from ESC
the battery and
indicates the throttle
wait for 2 seconds.
to be the highest.
The system is
ready to take off.
The ESC is powered
The prompt "♫123"
by a short beep to
indicates that the
indicate the number
normal system is
of lithium battery
ready for power-on.
segments.
The ESC issued the
Connect the ESC
"Bi-Bi-" indicate the
to the battery and
throttle to be the
wait for 2 seconds.
highest.
After completing the selection,
push up the throttle to
continue the function setting,
and drop down the throttle to
exit the setting.
Instructions for Brushless Motor ESC
Push the throttle to
the lowest and wait
for 1 second.
Push the throttle to
take off at any time.
Wait for about 4
seconds, the beep
sound "
means to enter the
function settings.
Function 1: Automatically detect the number of lithium batteries,
and set the protection voltage according to the number of detected
lithium batteries(each lithium battery protection voltage 2.8V)
Function 2: Protect 2 lithium batteries
Function 3: Protect 3 lithium batteries
Function 4: Low advance angle
Function 5: Medium advance angle
Function 6: High advance angle
Function 7: Restore factory defaults
Factory default setting: automatic detection of the number of
lithium batteries, low advance angle.
The sound of short
beep indicates the
number of lithium
battery protection.
Loops 1-7 sounds,
♫12345
corresponding to 1-7
"
function settings.