Pioneer DEH-3900MP Руководство по установке
Просмотреть онлайн или скачать pdf Руководство по установке для Автомобильный приемник Pioneer DEH-3900MP. Pioneer DEH-3900MP 9 страниц. Cd rds receiver
Также для Pioneer DEH-3900MP: Руководство по эксплуатации (20 страниц)
Печатать страницу
DEH-3900MP
DEH-2920MP
DEH-2900MP
DEH-2900MPB
DEH-1920R
DEH-1900R
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen Kabelfarben.
Le code de couleur des câbles utilisé pour ce produit
est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
чÌÌÓ ÛÒÚÓÈÒÚ‚Ó ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ ÌÓ‚˚Ï
Ú·ӂ‡ÌËflÏ Í ˆ‚ÂÚÛ ÔÓ‚Ó‰Ó‚.
Printed in Thailand
Imprimé en Thaïlande
<CRD4131-A/N> EW
<KSNNX> <06H00000>
Installation
Note:
DIN Front-mount
•
Check all connections and systems before final
installation.
Installation with the rubber bush
•
Do not use unauthorized parts. The use of
Mounting sleeve
unauthorized parts may cause malfunctions.
Dashboard
•
Consult with your dealer if installation requires
drilling of holes or other modifications of the
182
vehicle.
Rubber bush
53
•
Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
Screw
of a sudden stop.
•
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
1. Insert the mounting sleeve into the dashboard.
•
Optimum performance is obtained when the unit
•
When installing in a shallow space, use a sup-
is installed at an angle of less than 60°.
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
60°
2. Secure the mounting sleeve by using a screwdriv-
er to bend the metal tabs (90°) into place.
3. Install the unit as illustrated.
Removing the Unit
DIN Front/Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. (When reattaching the
This unit can be properly installed either from
trim ring, point the side with a groove down-
"Front" (conventional DIN Front-mount) or
wards and attach it.)
"Rear" (DIN Rear-mount installation, utilizing
•
It becomes easy to remove the trim ring if the
threaded screw holes at the sides of unit chassis).
front panel is released.
For details, refer to the following installation
methods.
Trim ring
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
ENGLISH
DIN Rear-mount
Fastening the front panel
1. Extend top and bottom of the trim ring outwards
If you do not plan to detach the front panel, the
to remove the trim ring. (When reattaching the
front panel can be fastened with supplied screw.
trim ring, point the side with a groove down-
wards and attach it.)
•
It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
Screw
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.
3. Tighten two screws on each side.
Use either truss screws (5 mm × 8 mm) or
•
flush surface screws (5 mm × 9 mm), depend-
ing on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket