Pioneer VSX-D6025 Руководство по эксплуатации - Страница 39

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Стереоприемник Pioneer VSX-D6025. Pioneer VSX-D6025 44 страницы.

Печатать страницу

Pioneer VSX-D6025 Руководство по эксплуатации

REMOTE CONTROL OPERATION

MULTI-EDIT MODE

A maximum

of seven commands

can be programmed

into MULTI

COMMAND button. This enables a series of signals to be transmitted

simply by pushing the MULT! COMMAND

button.

(Example} Programming the following three commands into the MULTI

COMMAND

button.

@ RECEIVER POWER

@ RECEIVER FUNCTION CD

@ CD PLAY (>)

1. Press the EDIT button. (Switches to the EDIT mode)

sequence,

. Press the MULTI COMMAND button. (Switches to the MULTI-EDIT

mode)

@ The CONTROL MODE buttons flash at random.

. Press the RECEIVER POWER button.

¢@ The CONTROL MODE buttons go out, and then flash at random.

(Registration is completed)

. Press the CD receiver input selector button.

(Registration is completed)

. Press the CD CONTROL MODE button.

* The CD button flashes.

Press the PLAY (

) button.

* The CD button goes out, and then the CONTROL MODE buttons

flash at random. (Registration is completed)

. Press the MULT] COMMAND button.

registration has been completed), and then the VCR 1, VCR 2, and

TV buttons flash in sequence.

8. Press the EDIT button.

¢ The EDIT mode is canceled.

If you press the MULTI COMMAND button, these remote control signals

are transmitted in the order programmed, so if CONTROL IN/OUT is

connected (refer to page 16), and if remote control signals can reach

both the receiver and CD player sensor windows, power to the receiver

switches on, the input selector switches to CD, and the CD player starts

playing. (When the CD piayer's power cord is plugged into the receiver's

switched AC OUTLET.)

NOTE:

After pressing the seventh command,

the MULTI-EDIT mode is

registered automatically (The VCR 1, VCR 2, and

TV CONTROL MODE

buttons flash in sequence}, but the EDIT mode is not canceled. To

cancel the EDIT mode, press the EDIT button.

After memorizing six or less commands, if you cancel the EDIT mode

without pressing

the MULT!

COMMAND

button again, all the

registered commands are cleared, leaving the previous commands as

they were.

if a button is for transmission, even if it is not an operation button in

the selected CONTROL MODE, registration is still possible. (Buttons

such as the VCR 7 }a<t.)

In this case, during signal transmission, the CONTROL MODE button

momentarily lights, but the remote control code is not transmitted.

If the component to be operated is installed at a distance, if there is

an obstacle between a specific component sensor window and the

remote control, or if component operation speeds are very different,

MULTI-COMMAND

operation may be incorrect.

When repeating

operations, first return to the initial settings for each component. For

operations such as power ON/OFF, if components are switched ON,

they can be switched OFF by transmitting a signal.

RETURNING TO THE INITIAL SETTINGS

Initialization of particular CONTROL MODES

Remove the battery compartment cover.

While pressing the M.CLEAR button inside the cover, press the

button for the CONTROL MODE (for example VCR 1) you want

to initialize.

¢ For example, if you initialize VCR 1 using the method mentioned

above, the CONTROL MODE button lights for about one second,

and the VCR 1 operation buttons are initialized.

M.CLEAR button

Initializing the entire memory

Remove the battery compartment cover.

While pressing the M.CLEAR button inside the cover, press the

RESET button.

* Do not release the M.CLEAR button before releasing the RESET

button. While pressing the M.CLEAR button, press the RESET

button, and quickly release.

Initialization is not possible if the buttons are pressed in the reverse

order.

in the MULTI COMMAND

button is cleared.

M.CLEAR button