Pioneer GM-102X1H/UC Руководство - Страница 4

Просмотреть онлайн или скачать pdf Руководство для Усилитель Pioneer GM-102X1H/UC. Pioneer GM-102X1H/UC 5 страниц. Bridgeable power amplifier

Печатать страницу

GM-202,102

Connecting The Unit

& CAUTION

Remove the negative (-) terminal of the

battery to avoid the risk of short-circuit

and damage to the unit.

Secure the wiring with cable clamps or

adhesive tape, To protect the wiring,

wrap adhesive tape around them where

they lie against metal parts.

ff you drill a hole in the engine compart-

ment to directly connect the special red

battery lead to the car battery, plug the

hole with a rubber bushing to protect the

wire. f a rubber bushing is not used, the

insulation may be damaged and a short

circuit may result due to the vibrations of

the car.

Do not route wires where they will get

hot, for example where the heater will

blow over them. If the insulation heats

up, it may become damaged, resulting in

4 short-circuit through the vehicle body.

Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, handbrake or seat stiding

mechanism.

Do not shorten any leads. Otherwise the

protection circuit may fail ta work when it

should.

Never feed power to other equipment by

cutting the insulation of the power supply

wire to tap from the wire. The current

capacity of the wire will be exceeded,

causing overheating.

(Fig. 11)

(6]

(7)

{8}

{9}

Special red battery wire

Connect to unswitched source greater

than 15 A.

Ground wire (black)

Connect ta metal body or chassis

Fuse (15 A)

Car stereo with RCA output pin jacks

{10} Externat output

(11] White

(12) Red

(13] Connecting wires with RCA pin plugs.

{sold separately)

{14] RCA input pin jack

{15} Blue

Connect the rnaie terminal of this wire

fo the blue wire of the car stereo

{system control terminal}. The female

terminal can be connected te the auto:

antenna

relay control terminal

if the car stereo does not have a

system remote control terminal,

connect the male terminal to the power

terminal through the ignition switch.

[16] Speaker output terminal

See the "Connecting the Speakers"

section for speaker connection

instructions

+ Be sure to use the special red battery wire

suppiied with the amplifier and connect

unswitched source greater than 15 A. Use

the supplied black ground wire and

connect to the vehicle body. {The sup-

plied special red battery and ground

wires are designed so that the amplifier

can be connected safely.}

OQ To prevent damage

+ Do not ground the speaker wire directly

or connect a negative {-) wire for several

speakers.

Speakers to be connected to the amplifier

should conform with the standards listed

below. Otherwise damage will be caused

to the speaker. The speaker impedance

must be 2 to 8 ohms.

Speaker

Power

_Channvel |

Type

Nominal input:

Sub-woofer | Min sey

Two-channel pt

| Other than

| Max. input

sub-woofer | Min. 70W

Nominal input

Sub-woofer | Min. 80 Ww

One-channel

ANG

CEAEaE

Other than | Max. input

sub-woofer | Min. 160 W _

Connecting the Power Terminal

Be sure to use the special red battery wire

supplied with the amplifier and connect

unswitched source greater than 15 A. Use

the supplied black ground wire and

connect to the vehicle body. (The sup:

plied special red battery and ground

wires are designed so that the amplifier

can be connected safely.)

Connect the special red battery wire to the

POWER terminal (+), and the black ground

wire to the GND terminal (~).

POWER

terminal

Terminal

screw

Terminal

screw

GND.

terminal

fee)

Ground wire

(black?

Special red

battery wire

Fig. 12

Fig. 13

Securely fasten the special red battery

wire and the ground wires with terminal

screws.

+ This unit is for vehicles with a 12-volt

battery and negative grounding. Before

installing it in a recreational vehicle, truck,

or bus, check the battery voitage.

install and route the special red battery

wire supplied with the amplifier as

faraway as possible from the speaker

wires. Install and route the battery wire,

ground wire, speaker wires, and the

amplifier as faraway as possible from the

antenna, antenna cable and tuner.

Connecting the Speakers

The speaker output mode can be two

channel (stereo), one-channel (mono), or

three-channel (stereo + mono). To connect

the speaker wires to suit the mode. Connect

the speakers according to the figure below.

Two-channel mode (stereo)

Green cover

Spesk

Green stripe

peaker

(left)

Speaker

right)

prea

One-channal mode {mano}

Black cover

Fig. 14

Grean cover

No CONNectign

—

Green stripe

peaker

ronal

Biack stripe

Black cover

Fig. 15