Pioneer GM-4000F Руководство пользователя - Страница 4
Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель Pioneer GM-4000F. Pioneer GM-4000F 8 страниц. Bridgeable four-channel power amplifier
Также для Pioneer GM-4000F: Руководство пользователя (6 страниц)
Печатать страницу
Installation
Example of installation on the floor
CAUTION
mat or on the chassis
• Do not install in:
—Places where it could injure the driver or pas-
sengers if the vehicle stops suddenly.
1. Place the amplifier where it is to be
—Places where it may interfere with the driver,
installed. Insert the supplied tapping
such as on the floor in front of the driver's
× 18 mm) into the screw
screws (4
seat.
• Make sure that wires are not caught in the sliding
holes. Push on the screws with a
mechanism of the seats, resulting in a short-cir-
screwdriver so they make marks
cuit.
where the installation holes are to be
• Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier.
located.
Protect all cables and important equipment such
as fuel lines, brake lines and electrical wiring
2. Drill 2.5 mm (1/8 inch) diameter
from damage.
holes at the point marked, and
• Install tapping screws in such a way that the
install the amplifier, either on the
screw tip does not touch any wire. This is impor-
tant to prevent wires from being cut by vibration
carpet or directly to the chassis.
of the car, which can result in fire.
• To prevent electric shock, do not install the ampli-
Tapping-screws
fier in places where it might come in contact with
(4 × 18 mm)
liquids.
• To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
CAUTION:
To prevent malfunction and/or injury
• To ensure proper heat dissipation of the amplifier,
be sure of the following during installation.
Drill a 2.5 mm (1/8 inch)
—Allow adequate space above the amplifier for
diameter hole
proper ventilation.
—Do not cover the amplifier with a floor mat or
carpet.
• Do not install the amplifier near a door where it
may get wet.
• Do not install the amplifier on unstable places
such as the spare tire board.
• The best location for installation differs with the
car model and installation location. Secure the
amplifier at a sufficiently rigid location.
• Make temporary connections first and check that
the amplifier and the system operate properly.
• After installing the amplifier, confirm that the
spare tire, jack and tools can be easily removed.
Specifications
Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)
Grounding system ............................................................................................................................................ Negative type
Current consumption ........................................................................................................ 18.1 A (at continuous power, 4 Ω)
Average current drawn* .......................................................................................................... 6.6 A (4 Ω for four channels)
Fuse .................................................................................................................................................................................. 25 A
Dimensions ........................................................................................................................ 300 (W) × 61 (H) × 237 (D) mm
Weight ........................................................................................................ 3.8 kg (8.4 lbs) (Leads for wiring not included)
Maximum power output ...................................................................................................................... 70 W × 4 / 150 W × 2
Continuous power output .......................................................... 35 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD)
70 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)
40 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)
Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)
Frequency response ............................................................................................................ 10 — 50,000 Hz (+0 dB, –1 dB)
Signal-to-noise ratio ...................................................................................................................... 100 dB (IHF–A network)
Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)
Separation ........................................................................................................................................................ 60 dB (1 kHz)
Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz
High pass filter ................................................................................................................................ Cut off frequency: 80 Hz
Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.4 — 6.5 V)
Note:
• Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
• The average current drawn is nearly the maximum current drawn by this unit
Floor mat
when an audio signal is input. Use this value when working out total current
or chassis
drawn by multiple power amplifiers.
9.0 A (4 Ω for two channels)
[12 (W) × 2-3/8 (H) × 9-3/8 (D) in]
(Bridge connection: 4 — 8 Ω allowable)
Cut off slope: –12 dB/oct
Cut off slope: –12 dB/oct
Speaker: 26 V/40 kΩ (1.6 — 26 V)