Pioneer SA-V210 Руководство по эксплуатации - Страница 6

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Усилитель Pioneer SA-V210. Pioneer SA-V210 8 страниц. Stereo mixing amplifier
Также для Pioneer SA-V210: Руководство по эксплуатации (23 страниц)

Печатать страницу

PANEL FACILITIES

(Z MIC volume controls (MIC 1, 2 and 3)

To adjust the respective microphones'

volume level against

the music. source

Normally,

keep the MAIN

VOLUME

control near the 5 -

position and use the MIC controls to adjust the volumes.

@ MIC 3 ECHO switch ( ON, 9, OFF)

This

switch

controls

only the echo

for the microphone

input. Pressing this switch turns off the echo.

@ KEY CONTROL switches/indicators

Press to change the pitch of the music. source.

Key for standard setting.

Mtl

A maximum

raise of four tones above the setting of the

standard key is possible in semitone-steps.

Mbt

— b4

A maximum

decrease of four tones below the setting of

the standard key is possible in semitone-steps.

NOTE:

No key change is possible when "CABLE" has been selected by

the input selector.

( AUTO SOURCE SELECTOR indicators

This unit automatically select the input source signals with

priority in the order of LASERDISC, VCR,TAPE/AUX and CABLE.

These indicators display the output source accordingly.

OPERATION

4 ECHO adjusting controls

Controis the microphone echo characteristics.

@ DELAY

Adjusts

the echo

delay time.

Setting

higher,

the

echo

intervals become longer, resulting in stronger echo effect.

@ REPEAT

Adjusts the echo repeat times.

Setting higher, the echo

repeat times increase, resulting in stronger echo effect.

NOTE:

* When

the

DELAY

control

is adjusted

while

using

the

microphone,

the pitch may be changed:

¢ df the REPEAT control is set too high, echo may never stop. In

such a case, readjust the REPEAT

control.

12: MAC and KEY CONTROLLER jacks

Three microphones can be connected simultaneously.

When using a microphone with key control switch, connect it

to MIC 1 of MIC 2 jack. And be sure to connect the control

cable to the KEY CONTROLLER

jack.

13) MIC TONE controls

These

controls

adjust

the

tone

(BASS/TREBLE)

for

microphones 1, 2 and 3.

BASS:

Adjusts the low-frequency tone.

TREBLE:

Adjusts the high-frequency tone.

The numbers following the names of switches and controis in

this section correspond to the numbers shown in the "FRONT

PANEL."

1..Turn the power ON to the SA-V210

and other

components.

* When using an LD player, Turn on the TV monitor.

2. Connect the microphone(s} to the MIC jack(s} 12.

3. Set the MAIN VOLUME control 2 as desired (e.g.

set to 5 — 7}.

4. Start playback. Adjust the volume level with the

MUSIC

control

3 and speaker balance with the

BALANCE control

5. Speak or sing with the microphone and adjust the

volume level with the MIC volume control (7).

6. Adjust the sound with the MUSIC

TONE controls

©,

ECHO

adjusting

controls

if, MIC

TONE

controts 13, and MIC ECHO control 6: as desired.

7. Select the desired key with the KEY CONTROL

switches '9).

AUTO SOURCE SELECTOR

The SA-V210 automatically selects and outputs all input signals

according to the following priority.

} LASERDISC

2 VCR

3 TAPE/AUX

4 CABLE

The input sensitivity of VCR and TAPE/AUX can be changed by the

SOURCE SELECTOR SENSITIVITY switch on the rear panel

Automatic output switching of TV monitor

When the LD piayer is in stop mode, VIDEO signals from VISUAL

INPUT jack 2 (VCR/CAMERA)

will be output from the VISUAL

OUTPUT jacks 1, 2 and 3 to the monitor.

Fade-in function for cable

When the SA-V210 is switched from LASERDISC, VCR or TAPE/AUX

mode to CABLE mode, the fade-in circuit activates and the volume

level gradually increases to the level that has been set by the MAIN

VOLUME contro! after approx. 2 to 8 seconds.