Pioneer DEH-P6400 Руководство по установке
Просмотреть онлайн или скачать pdf Руководство по установке для CD-плеер Pioneer DEH-P6400. Pioneer DEH-P6400 4 страницы. Multi-cd control high power cd player with fm/am tuner
Также для Pioneer DEH-P6400: Руководство по эксплуатации (48 страниц)
DEH-P6400
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD3531-A/N> UC
<KKNZF/01H00000>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
• When this product's source is switched ON, a con-
negative grounding. Before installing it in a recre-
trol signal is output through the blue/white lead.
ational vehicle, truck, or bus, check the battery
Connect to an external power amp's system remote
voltage.
control or the car's Auto-antenna relay control ter-
• To avoid shorts in the electrical system, be sure to
minal (max. 300 mA 12 V DC). If the car features
disconnect the ≠ battery cable before beginning
a glass antenna, connect to the antenna booster
installation.
power supply terminal.
• Refer to the owner's manual for details on con-
• When an external power amp is being used with
necting the power amp and other units, then make
this system, be sure not to connect the blue/white
connections correctly.
lead to the amp's power terminal. Likewise, do not
• Secure the wiring with cable clamps or adhesive
connect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tape
of the auto-antenna. Such connection could cause
around them where they lie against metal parts.
excessive current drain and malfunction.
• Route and secure all wiring so it cannot touch any
• To avoid short-circuiting, cover the disconnected
moving parts, such as the gear shift, handbrake
lead with insulating tape. Especially, insulate the
and seat rails. Do not route wiring in places that
unused speaker leads without fail. There is a possi-
get hot, such as near the heater outlet. If the insula-
bility of short-circuiting if the leads are not insulat-
tion of the wiring melts or gets torn, there is a dan-
ed.
ger of the wiring short-circuiting to the vehicle
• To prevent incorrect connection, the input side of
body.
the IP-BUS connector is blue, and the output side
• Don't pass the yellow lead through a hole into the
is black. Connect the connectors of the same colors
engine compartment to connect to the battery. This
correctly.
will damage the lead insulation and cause a very
• If this unit is installed in a vehicle that does not
dangerous short.
have an ACC (accessory) position on the ignition
• Do not shorten any leads. If you do, the protection
switch, the red lead of the unit should be connected
circuit may fail to work when it should.
to a terminal coupled with ignition switch ON/OFF
• Never feed power to other equipment by cutting
operations. If this is not done, the vehicle battery
the insulation of the power supply lead of the unit
may be drained when you are away from the vehi-
and tapping into the lead. The current capacity of
cle for several hours. (Fig. 1)
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
ACC position
No ACC position
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.
Front output
16 cm [5/8 in]
Rear output or
Multi-CD player
Subwoofer output
(sold separately)
Antenna jack
IP-Bus input(Blue)
IP-BUS cable
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lightnig switch terminal.
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect anything to
Fig. 1
the speaker leads that are not connected to speakers.
Use this for connections when you have the separately
available amplifier.
Connecting cords
with RCA pin plugs
(sold separately)
Fuse
This Product
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
System remote control
+
+
Front speaker
≠
≠
White
Gray
+
+
Front speaker
≠
≠
White/black
Gray/black
Left
Green
Violet
+
+
Rear speaker or
Subwoofer
≠
≠
Green/black
Violet/black
+
+
Rear speaker or
Subwoofer
≠
≠
Note:
When a subwoofer is connected to this unit instead of a rear
speaker,change the the rear output setting in the Initial
Setting. (refer to the Operation Manual)
The subwoofer output of this unit is monaural.
<ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Front speaker
Front speaker
Right
Rear speaker or
Subwoofer
Rear speaker or
Subwoofer
Fig. 2