Pioneer S-7EX XTW/E Руководство по эксплуатации - Страница 7

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Акустическая система Pioneer S-7EX XTW/E. Pioneer S-7EX XTW/E 10 страниц. Ex series
Также для Pioneer S-7EX XTW/E: Каталог (20 страниц), Руководство по эксплуатации (24 страниц), Брошюра и технические характеристики (16 страниц)

Печатать страницу

Pioneer S-7EX XTW/E Руководство по эксплуатации

2.3 NETWORK ASSY

Before removing the Network Assy, remove the grille and each speaker unit then disconnect the cords from the

speaker unit.

• For removal/reattachment of the Network Assy for the woofer: Only the woofer must be removed.

• For removal/reattachment of the Network Assy for the midrange/tweeter: Removal of all the units is required.

2.3.1 Network Assy for the Woofers

• The Network Assy for the woofers is located inside the

back board behind the right woofer and secured with 4

screws.

(1) Remove the acoustic absorbent pads that are located

on the input terminals and behind the chamber.

(See Figs. 2-5 to 2-8.)

(2) Remove the 2 nuts that secure the round connectors

from the lower input terminals.

(See Fig. 2-1. Tool: Box wrench, 14 mm/GGH-002)

(3) Remove the 4 screws that secure the Network Assy

then pull the Assy out through the hole where the

woofer was attached.

(4) When reattaching, pass the Network Assy through the

hole where the woofer was attached then secure it in

place with the 4 screws.

(5) Among the 3 pairs of cords from the Network Assy,

connect the cords with the round connectors to the

lower input terminals and secure them with the nuts.

(See Fig. 2-1. Tool: Box wrench, 14 mm/GGH-002)

(6) Apply adhesive to the secured nuts.

(Adhesive: DIABOND black/GYL-014)

(7) Reinstall the acoustic absorbent pads, at the input

terminals and behind the chamber.

(See Figs. 2-5 to 2-8.)

(8) Connect and solder the remaining 2 pairs of cords

from the Network Assy to the woofers and reinstall the

woofer in the cabinet.

Upper side

White with Black line

From the Network Assy

for the midrange/ tweeter

From the Network Assy

for the woofers

Fig. 2-1: Input terminals (inside the cabinet)

Uppe side

Bottom side

: Screws

Fig. 2-2: Specifications for attaching

the Network Assy for the woofers

(See Fig. 2-2.)

Apply adhesive.

-: White

Back-board side

Baffle-board side

: Screws

Fig. 2-3: Specifications for attaching the

Network Assy for the midrange/tweeter

S-7EX

2.3.2 Network Assy for the midrange /

tweeter

• The Network Assy for the midrange/tweeter is located

inside the bottom board behind the left woofer and

secured with 4 screws.

(1) Remove the acoustic absorbent pads that are located

at the input terminals, inside and at the rear of the

chamber, and behind the chamber.

(See Figs. 2-5 to 2-8 and 2-9 to 2-11.)

(2) Remove the 2 nuts that secure the round connectors

from the upper input terminals.

(See Fig. 2-1. Tool: Box wrench, 14 mm/GGH-002)

(3) Remove the 4 screws that secure the closure panel

inside the chamber, remove the 4 screws that

secure the Network Assy, and pull the Network Assy

out through the hole where the woofer was attached.

(See Figs. 2-3 and 2-4. Tool: Screwdriver/GGK1012)

(4) When reattaching, pass the Network Assy through the

hole where the woofer was attached and secure it in

place using the 4 screws.

(See Fig. 2-3. Tool: Screwdriver/GGK1012)

(5) Among the cords from the Network Assy, connect the

cords with the round connectors to the upper input

terminals and secure them with the nuts.

(See Fig. 2-1. Tool: Box wrench, 14 mm/GGH-002)

(6) Apply adhesive to the secured nuts.

(Adhesive: DIABOND black/GYL-014)

(7) Pass the 2 pairs of cords from the closure panel

through behind the chamber then secure the closure

panel from inside the chamber, using the 4 screws.

(See Fig. 2-4.)

(8) Reinstall the acoustic absorbent pads at the input

terminals, inside the chamber, and behind the

chamber. (See Figs. 2-5 to 2-8 and 2-9 to 2-11.)

(9) Connect and solder the cords to the coaxial-unit

speaker and reinstall it in the cabinet.

Fig. 2-4: Specifications for attaching the

closure panel (cross-sectional view of the

coaxial-unit speaker)

Note: The NW Assy shown in

this photo is for the S-1EX,

but the shape of the closure

panel is the same.

Closure panel

: Screws

Chamber