Ariston CIS LI 460 A Инструкция по установке и использованию - Страница 20
Просмотреть онлайн или скачать pdf Инструкция по установке и использованию для Посудомоечная машина Ariston CIS LI 460 A. Ariston CIS LI 460 A 24 страницы.
Печатать страницуChoose where you want to install
your dishwasher, you can even
place it so that its sides or back
panel are side by side with furniture
or up against the wall. The
dishwasher is provided with water
supply and drain hoses, which can
be directed towards the left or right
to facilitate appropriate
installation.
Once the appliance is positioned,
adjust the feet by screwing them
in or out depending on how high
you want it and to level it so that it
is horizontal. Make sure that it is
not inclined more than 2 degrees.
If the appliance is level, it will he
lp ensure its correct operation.
Insert the appliance into the cutout
and then adjust the height using the
screws located on the front bottom
part of the machine. Use a
screwdriver to turn the screws in
the clockwise or anti-clockwise
direction to increase or decrease
the height respectively.
Connect the cold water supply
hose to a 3/4 gas threaded
connection, taking care to screw it
tightly onto the tap. If the water
hoses are new or have been out of
use for an extended period of time,
let the water run to make sure it is
clear and free of impurities before
making the connection. If this
precaution is not taken, the water
inlet could get blocked, causing
damage to your dishwasher.
- It is strongly recommended to
use a new hose to connect the
dishwasher to the water supply
line, and the old hose-set should
not be reused. Asking to specilized
shop or an authorized service
technician (see Service).
ARISTON DISHWASHER - Instructions for installation and use
Your dishwasher can be supplied
with hot water from the mains
supply (if you have a central heating
system with radiators) at a tempe-
rature of no more than 60°C.
In this case, the wash cycle time
will be about 15 minutes shorter
and the wash will be slightly less
effective.
The connection must be made to
hot water supply following the
same procedures as those indicated
for the cold water connection.
Your dishwasher is provided with a
special system which blocks the
water supply in the event of leaks
inside the appliance. It is further
equipped with a water inlet hose
that can withstand extremely high
pressures and that turns bright red
in the event of breakage. Safety in
the event of flooding is ensured by
the second clear hose that contains
the former and thus highlights the
latter when it has turned bright red.
It is vital that you check it on a
regular basis: if you see it has turned
bright red, then you know you have
to replace it as soon as possible.
Call for an authorised technical
engineer to come and replace it.
Fit the drain pipe into a drain line
with a minimum diameter of 4 cm
or place it over the sink. Avoid
restricting or bending it. The part
of the pipe marked with the letter
A should be between 40 and 100
cm above the ground.
The pipe should not be immersed
in water.
A
On some models, a transparent
condensation-proof adhesive tape
has been provided.
It should be stuck onto the lower
side of your wooden worktop to
protect it from the formation of
condensation.
When not provided, this tape can
be requested as a spare part from
authorised retailers.
First of all, check that the mains
voltage and frequency values
correspond to those stated on the
rating plate located on the stainless
steel inner door of the appliance
and that the electrical system to
which the dishwasher is connected
is sized for the maximum current
indicated on said rating plate.
Only now can you plug the
appliance into a socket provided
with an efficient earth connection
(the system's earthing is a
guarantee of safety provided for by
law, make sure your system has
it).
Once the appliance has been
installed, the electrical plug and
socket should remain accessible.
If the power supply cable is
damaged, it must be replaced by
the manufacturer or its Techni-
cal Assistance Service in order to
prevent all potential hazards. (See
Assistance)
The cable should not be bent or
compressed.
The Company shall not be held
responsible for any incidents that
occur if these regulations are not
observed.