Ariston PRO1 ECO Series Руководство - Страница 14

Просмотреть онлайн или скачать pdf Руководство для Водонагреватель Ariston PRO1 ECO Series. Ariston PRO1 ECO Series 19 страниц. Unvented

Печатать страницу

LEDs, with the other LEDs off). Each press of the button increases or decreases the set temperature by 10 degrees. After

5 seconds without any action, the set-point will be confirmed and memorised.

STALL STATUS

There are two possible stall statuses:

The Max function is deactivated even if there is a stall error, if the "OFF" status is engaged or if the +/– buttons are

- TOUCH CONTROL STALL STATUS

pressed to change the set-point.

If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled.

This status is indicated by the flashing of the temperature LEDs (fast if the product is on, slow if it is off).

Setting the set-point

- OTHER STALL STATUS

By pressing the PLUS or MINUS buttons, the user can choose the set-point temperature (indicated by the temperature

If other errors are detected, all the LEDs will start flashing.

LEDs, with the other LEDs off ). Each press of the button increases or decreases the set temperature by 10 degrees. After

To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on

5 seconds without any action, the set-point will be confirmed and memorised.

and off. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the

ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the

STALL STATUS

Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for

5 seconds.

There are two possible stall statuses:

- TOUCH CONTROL STALL STATUS

If a touch control error is detected, the status of the touch LED is undetermined and cannot be controlled. This status

is indicated by the flashing of the temperature LEDs (fast if the product is on, slow if it is off ).

USEFUL INFORMATION (for the user)

- OTHER STALL STATUS

Before any operation of cleaning the device make sure to turn off the product by bringing the external switch to the

If other errors are detected, all the LEDs will start flashing.

OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic

To reset a non-volatile error, if possible, it is necessary to press the ON/OFF button (Fig. 3) to switch the product on

material.

and off. To verify which error occurred, it is necessary to enter the diagnostics state by simultaneously pressing the

ON_OFF and MAX BUTTONS for 3 seconds. After 25 seconds, the system will return to the stall status. Note: for the

If the water delivery is cold, have the following checked:

Chinese market (set through NFC), the product is reset by simultaneously pressing the ON/OFF and ECO buttons for

5 seconds.

- that the device is connected to the power supply and the external switch is in the ON position.

- that at least led 40°C (1 fig. 3) is turned on.

If there is presence of steam output from the taps:

USEFUL INFORMATION (for the user)

Remove power from the electrical appliance and contact technical support.

Before any operation of cleaning the device make sure to turn off the product by bringing the external switch to the

If the hot water delivery is insufficient, have the following checked:

OFF position. Do not use insecticides, solvents or aggressive detergents that may damage the painted parts or plastic

- the pressure of the water mains;

material.

- eventual obstruction of the inlet and outlet pipes (deformation or sediment).

If the water delivery is cold, have the following checked:

Water trickling from the pressure safety device

- that the device is connected to the power supply and the external switch is in the ON position.

- that at least led 40°C (1 fig. 3) is turned on.

During the heating phase, some water may trickle from the tap. This is normal. To prevent the water trickling, a suitable

expansion vessel must be installed on the flow system. If the trickling continues even after the heating phase, have the

If there is presence of steam output from the taps:

following checked:

Remove power from the electrical appliance and contact technical support.

- device calibration;

- the pressure of the water mains.

If the hot water delivery is insufficient, have the following checked:

Caution: Never obstruct the appliance outlet!

- the pressure of the water mains;

- eventual obstruction of the inlet and outlet pipes (deformation or sediment).

IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE

BY A QUALIFIED TECHNICIAN.

IF THE PROBLEM PERSISTS,NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE

BY A QUALIFIED TECHNICIAN.

The indicated data and specifications are not binding; the manufacturer reserves the right to modify them at his

own discretion notification or replacement.

The indicated data and specifications are not binding; the manufacturer reserves the right to modify them at his

own discretion notification or replacement.

This product conforms to Directive WEEE 2012/19/EU.

The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the prod-

The symbol of the crossed waste paper basket on the appliance and its packaging indicates that the product must be

uct must be scrapped separately from other waste at the end of its service life. The user must therefore

scrapped separately from other waste at the end of its service life. The user must therefore hand the equipment over to a

sorted waste disposal facility for electro-technical and electronic equipment at the end of its service life.

hand the equipment over to a sorted waste disposal facility for electro-technical and electronic equipment

Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.

at the end of its service life.

Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area is at least 400

Alternatively, he may return the equipment to the retailer at the time of purchase of a new equivalent type of appliance.

for disposal free of charge and without any obligation to purchase new product.

Electronic equipment of size less than 25 cm can be handed over to any electronics equipment retailer whose sales area

is at least 400 m2 for disposal free of charge and without any obligation to purchase new product.