Ariston INTESA TP30 Руководство пользователя, инструкции по установке и обслуживанию - Страница 13

Просмотреть онлайн или скачать pdf Руководство пользователя, инструкции по установке и обслуживанию для Котел Ariston INTESA TP30. Ariston INTESA TP30 50 страниц.

Печатать страницу
Installation
face of the flue elbow (X - F
ment, you now have the total length of flue required (including the
terminal), this figure must now be subtracted from 860mm, you
now have the total amount to be cut from the plain end of the flue.
Cut the flue to the required length ensuring that the distance
between the inner and the outer flue is maintained (F
e.g. X = 508mm + 22mm = 530mm
860 - 530 = 330mm (Length to be cut from the plain end
of the flue).
Once cut to the required length, ensure that the flue is free from
burrs and reassemble the flue. If fitting the flue from inside of the
building attach the grey outer wall seal to the flue terminal and
push through the flue through the hole, once the wall seal has
passed through the hole, pull the flue back until the seal is flush
with the wall. Alternatively, the flue can be installed from outside
of the building, the grey outer seal being fitted last.
Fitting the Telescopic Flue Kit (Horizontal)
C
:
ONTENTS
1
S
O-R
(60mm)
X
ILICONE
ING
1
E
(90
)
O
X
LBOW
2
W
S
(I
& E
X
ALL
EALS
NTERNAL
1
A
F
P
X
LUMINIUM
LUE
IPE INCLUDING
2
F
C
X
LUE
LAMPS
8
S
X
CREWS
2
S
X
EALS
The telscopic flue is suitable for use with an exact minimum X
dimension of 270mm and an exact maximum X dimension
470mm.
IMPORTANT!!
Do not extend the telescopic flue to an X dimension of more
than 470mm. If longer lengths are required use extension
pieces as necessary. Under no circumstances must the flue
be cut.
The wall must then be made good around the flue (ensuring a fall
o
of 1
is maintained away from the boiler to the flue terminal).
Once made good, place the inner (white) wall seal over the flue
and push up to the wall, secure the flue to the elbow by using the
clamp supplied.
For each additional 90
o
elbow 1 metre must be removed from the
total flue length (maximum 4 metres including the 1st elbow). For
each additional 45
o
elbow 0.5 metre must be subtracted from the
total flue length (F
6.13).
IG
Fitting the Coaxial Flue (Vertical)
(For Twin Pipe Instructions see page 14)
C
:
ONTENTS
1
S
O-R
(60mm)
X
ILICONE
ING
1
E
(90
)
O
X
LBOW
2
W
S
(I
& E
X
ALL
EALS
NTERNAL
1
A
F
P
X
LUMINIUM
LUE
IPE INCLUDING
2
F
C
X
LUE
LAMPS
8
S
X
CREWS
2
S
X
EALS
The vertical flue kit is supplied with a specially designed weather
proof terminal fitted, it can be used either with a flat roof or a
pitched roof. (see F
6.12, 6.13).
IGS
Supplied By www.heating spares.co Tel. 0161 620 6677
6.8), add 22 mm to this measure-
IG
6.10).
IG
)
XTERNAL
T
(T
- 60/100)
ERMINAL
ELESCOPIC
)
XTERNAL
T
(T
- 60/100)
ERMINAL
ELESCOPIC
25 mm
25 mm
F
6.11
IG
F
6.12
IG
13
F
6.9
IG
F
6.10
IG
WARNING
IT WILL BE NECESSARY
T
TO
CONSULT
ABLE
6.1
18
ON PAGE
TO
DETERMINE WHETHER
THE FLUE RESTRICTOR
.
IS REQUIRED
SHOULD
,
IT NOT BE NEEDED
THE RESTRICTOR WILL
NEED TO BE REMOVED
FROM THE FLUE GAS
(F
. 6.11).
COLLAR
IG