Ariston FTGHL 751 D/IX/A LPG Руководство по эксплуатации - Страница 7

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Варочная панель Ariston FTGHL 751 D/IX/A LPG. Ariston FTGHL 751 D/IX/A LPG 32 страницы.

Печатать страницу

• Where the hob is not installed over a built-in oven, a wooden panel must

be installed as insulation. This must be placed at a minimum distance of

20 mm from the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely flat surface with an opening of at least 45 x 560

mm (see diagrams).

! The hob can only be installed above built-in ovens with a cooling ventilation

system.

Electrical connection

Hobs equipped with a three-pole power supply cable are designed to operate

with alternating current at the voltage and frequency indicated on the data

plate (this is located on the lower part of the appliance). The earth wire in the

cable has a green and yellow cover. If the appliance is to be installed above

a built-in electric oven, the electrical connection of the hob and the oven must

be carried out separately, both for electrical safety purposes and to make

extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate.

The appliance must be directly connected to the mains using an omnipolar

circuit-breaker with a minimum contact opening of 3 mm installed between the

appliance and the mains. The circuit-breaker must be suitable for the charge

indicated and must comply with current electrical regulations (the earthing

wire must not be interrupted by the circuit-breaker). The supply cable must

not come into contact with surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical connection has been

made and that it is compliant with safety regulations.

Before connecting to the power supply, make sure that:

• the appliance is earthed and the plug is compliant with the law.

• the socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• the voltage is in the range between the values indicated on the data plate.

• the socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures not

be observed.

Gas connection

The appliance should be connected to the main gas supply in compliance with

current national regulations. Before carrying out the connection, make sure

the cooker is compatible with the gas supply you wish to use G31-37mbar or

G30-30mbar (Liquid Gas).

! Check that the pressure of the gas supply is consistent with the values

indicated in Table 1 )"Burner and nozzle specifications"(. This will ensure the

safe operation and longevity of your appliance while maintaining efficient

energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a way as not to

place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe fitting on the appliance supply ramp

and this is fitted with a seal in order to prevent leaks. The seal must always

be replaced after rotating the pipe fitting )seal provided with appliance(. The

gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a threaded

attachment

The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.

These pipes must be installed so that they are never longer than 2000 mm

when fully extended. Once connection has been carried out, make sure that

the flexible metal pipe does not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the pipe fittings for leaks

using a soapy solution. Never use a flame.

Adapting to G30 gas

! This procedure must be performed by a qualified technician authorised

by the manufacturer.

! Once this procedure is finished, replace the old rating sticker with one

indicating the new type of gas used. Stickers are available from any of our

Service Centres.

! Should the gas pressure used be different (or vary slightly) from the

recommended pressure, a suitable pressure regulator must be fitted to the

inlet pipe (in order to comply with current national regulations).

DATA PLATE

Electrical

see data plate

connections

ECODESIGN

This appliance conforms to the EU Regulation no. 66/2014

implementing Directive 2009/125/EC.

standard EN 30-2-1