Whirlpool AWM 9100 GH Руководство по эксплуатации - Страница 9
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Стиральная машина Whirlpool AWM 9100 GH. Whirlpool AWM 9100 GH 15 страниц.
Печатать страницу
Final spin results are poor:
The appliance has an imbalance detection and
correction system. If individual heavy articles are
loaded (bathmat, bathrobe, etc.) this system may
reduce the spin speed automatically to protect the
appliance or even interrupt the spin cycle
altogether, if the imbalance is too great even after
several spin starts.
• If the laundry is still too wet at the end of the
cycle, add other articles of laundry and repeat
the spin cycle.
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (if available) point to the source of the fault.
Fault description table
Small lamp lights up
"Water tap closed"
-
-
"Water Stop"
a. Water inlet fault (no water or insufficient
water pressure)
The "Water tap closed" indicator is on and the
digital display shows "FH" Switch off the
appliance by turning the programme selector to
the "
" position and unplug it.
Check whether:
• the water tap is open and the water supply
pressure is sufficient;
• the water inlet hose is kinked;
• the mesh filter between the tap and the hose is
clean (see "Care and Maintenance" / "Mesh filter
in water connection");
• the water supply hose is frozen up.
Connect the appliance to the electrical supply.
Reselect the desired programme and press the
"Start/Pause" button again to continue with
the programme (do not add detergent for this
programme)
b. Draining fault
The digital display shows "FP". Switch off the
appliance by turning the programme selector to
the "
" position and unplug it.
Check whether:
• the drain hose is kinked (see "Installation");
IMPORTANT: before draining, allow the wash
water to cool down.
• the drain hose is frozen.
Connect the appliance to the electrical supply.
Reselect the desired programme and press the
"Start/Pause" button again to continue with
the programme (do not add detergent for this
programme). If the fault re-occurs, contact After
Sales Service (See "After Sales Service").
• Excessive foam formation may prevent spinning.
Ensure correct amount of detergent is used.
• Check whether the spin speed has been reduced
to 0.
No water or insufficient water pressure for
appliances with safety hose:
• the appliance has a safety hose and the safety
valve has opened (red indicator in the safety
valve inspection window).
In this case replace it with a new safety hose.
Digital display
"FH"
"FP"
from "F4" to "F21"
"FA"
c. Electrical module fault
The digital display shows "F4" to "F21".
• Set the programme selector to the "
position, select the desired programme and
press the "Start/Pause" button again. The
programme will continue.
• If the fault re-occurs, contact After Sales
Service (See "After Sales Service").
d. Water Stop fault
An audible tone sounds. The light of the Water
Stop indicator goes on. The digital display
shows "FA" and the pump is running.
The "Water Stop fault" may have been triggered by:
• too much foam.
• a leak in the appliance, water running into the
water tank.
1.Switch off the appliance by turning the
programme selector to the "
unplug the appliance and turn off the tap.
2.Tilt the appliance forwards carefully to allow the
collected water to flow out,
3.plug the washing machine in again and turn on
the tap,
4.reselect the desired programme and press the
"Start/Pause" button (there is no need to add
additional detergent). The programme will
continue. If the faults occurs again, call After-
Sales Service with details about the fault (see
"After Sales Service"),
5.If the "Start/Pause" button is not pressed but
water is still flowing into the machine, turn off
the water supply and inform After Sales Service
(see "After Sales Service").
Home
Fault description
"Water inlet fault"
"Draining fault"
"Electrical components fault"
"Water Stop fault"
" position,
Appliances
"