Whirlpool CAM2762KQ0 Руководство по установке - Страница 4
Просмотреть онлайн или скачать pdf Руководство по установке для Стиральная машина Whirlpool CAM2762KQ0. Whirlpool CAM2762KQ0 16 страниц. Commercial washer 120-volt, 60-hz models
Печатать страницу
Now start...
Excessive Weight Hazard
Use two or more people to move
and install washer.
Failure to do so can result in back
or other injury.
Usa now hoses and washers that came
with your Whirlpool washer.
Replace
inlet hoses after 5 years of use
to reduce
the risk of hose failure,
Inspect and replace
inlet hoses if
bulges, kinks, cuts, wear,
or leaks are
found,
When replacing
your inlet hoses,
mark the date of replacement
on the
label with a permanent
marker,
coupling
washer
m Insert a flat washer
into each end
of the inlet hoses, Check that washers
are firmly seated
in couplings,
Inlets are plastic.
Do Not stdp or
crossthroad.
shipping
lm
Remove
tape that covers
shipping
strap, Pull to
completely
remove
the shipping
strap with 2 colfferpins
from the inside
of the washer,
\
mPlace ho_e clamp
over washer
drain connector,
Push drain hose onto
washer connector,
Use pliers to open
clamp
and slide clamp
over drain
hose, Check for good
fit,
dmL
_[_D• Measure
and mark a point
approximately
16 inches (40,6 cm)
from the plug end of the shipping
strap, Cut this shipping
strap at this
point,
cold
Chock that hoso is not
water
twisted or kinked and is
inlet
socuroly in placo.
vaive
Put "hook"
end of drain
hose into standpipe,
Tightly wrap the shipping
strap around
the
Pull firmly to remove
the end of
shipping
strap from the back of the
washer, The shipping
strap plug must
be completely
removed
from the
washer for the self-leveling
legs to
be released,
hot water
inlet valve
standpipe,
Push plug into
the nearest hole in the
shipping
strap,
3
7•g ore
| aAltach
hose to boltom
inlet
alffaching
water
valve opening
first, Then second
hose
inlet hoses, run
to top inlet, Tighten couplings
by
water
through
=
hand; then use pliers to make an
both faucets
into
_'iit
additional
two-thirds
turn,
a bucket,
This will
get rid of particles
in water
lines that
might clog hoses,
Mark which
is the hot water
faucet,
_;mAltach
bolffom hose (inlet
marked
"H') to hot water
faucet,
Altach
top hose (inlet marked
"C') to
cold water
faucet,
Tighten coupling
to faucet
by hand; then use pliers to
B Move washer
close to final
make final two-thirds
turn,
Save tho shipping strap for uso in
Step 6.
position, Put "hook"
end of drain hose
into standpipe,
Estimate length of
drain hose needed
when washer is in
final position,
Hose must be cut
exactly
to length so "hook" end is
held tightly over edge of standpipe,
If
drain hose is too long, cut straight
end
of hose, (Do Not cut "hook"
shaped
and of drain hose.)
DO NOT FORCEEXCESS LENGTH OF
DRAINHOSEDOWN THESTANDPIPE.
THISCOULD CAUSESIPHONING. See
Step 6.
dllk
_
mStack two corner posts on top of
each other, Tilt washer backwards
and
insert corner posts 3 inches (7,6 cm) in
from one side of washer as shown,
Repeat with other corner posts on other
side of washer,
PAGE 4