Whirlpool WASHER Инструкции пользователя - Страница 14

Просмотреть онлайн или скачать pdf Инструкции пользователя для Стиральная машина Whirlpool WASHER. Whirlpool WASHER 15 страниц. Washing machine
Также для Whirlpool WASHER: Руководство по установке (16 страниц), Руководство по установке (27 страниц), Инструкции пользователя (8 страниц), Инструкции пользователя (20 страниц), Инструкции пользователя (24 страниц), Инструкции пользователя (8 страниц), Руководство по установке (20 страниц), Руководство по эксплуатации и уходу (40 страниц), Руководство по установке (16 страниц), Инструкции пользователя (8 страниц), Диаграмма программы (2 страниц), Инструкции по установке (5 страниц), Руководство по установке (8 страниц)

Печатать страницу

Whirlpool WASHER Инструкции пользователя

For standpipe or laundry tub drain systems:

1. Open yellow, single-wire clamp with pliers and slide over

hooked end of drain hose to secure the rubber and corrugated

sections together.

A. Hooked end

B. Drain hose

2. Put hooked end of drain hose into laundry tub or standpipe.

Rotate hook to eliminate kinks.

To prevent drain water from going back into the washer:

Do not straighten hooked end of drain hose. Do not force

excess drain hose into standpipe. Hose should be secure,

but loose enough to provide a gap of air.

Do not lay excess drain hose in bottom of laundry tub.

For floor drain installation, see kit number required under

"Tools and Parts."

Connect the Inlet Hoses

1. Insert new flat washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach a hose to the hot water faucet. Screw on coupling by

hand until seated on the washer.

3. Attach a hose to the cold water faucet. Screw on coupling by

hand until seated on the washer.

4. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

Clear the water lines

5. Run water through both faucets and inlet hoses, into a bucket

or laundry tub, to get rid of particles in the water lines that

might clog the inlet valve screens.

Connect the inlet hoses to the washer

6. Attach the hose that is connected to the hot water faucet to

the HOT (bottom) inlet valve. Attaching the hot water hose first

makes it easier to tighten connection with pliers. Screw on

coupling by hand until seated on the washer. Using pliers,

tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

A. Cold water inlet valve

B. Hot water inlet valve

NOTE: The inlet valve may be on the right or the left side of

the washer, depending on your model.

7. Attach the hose that is connected to the COLD water (top)

inlet valve. Screw on coupling by hand until seated on the

washer. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

Check for leaks

8. Turn on the water faucets and check for leaks. A small amount

of water might enter the washer. You will drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates for future reference.

If you connect only one water hose, you must cap off the

remaining water inlet port.

Periodically inspect and replace hoses if bulges, kinks,

cuts, wear, or leaks are found.