Whirlpool Cabrio WED8000D Руководство по эксплуатации - Страница 24
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Сушилка Whirlpool Cabrio WED8000D. Whirlpool Cabrio WED8000D 30 страниц. Smart electronic dryer
Печатать страницу
Troubleshooting — Dryer Operation
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help.
If you experience
Dryer Results (cont.)
Drying times are too
long and clothes are not
getting dry
Cycle time is too short
Lint on load
Stains on load
Stains on drum
Loads are wrinkled
Odors
22
Possible Causes
The load is too large and heavy to dry
quickly.
Fabric softener sheets are blocking
the grille.
The dryer is located in a room with
temperature below 45ºF (7ºC).
The dryer is located in a closet.
The load may not be contacting the
sensor strips on Automatic Cycles.
Clothes are coming out of the
Steam Refresh cycle with damp
or wet spots.
The automatic cycle is ending early.
Lint screen is clogged with lint.
Improper use of fabric softener.
Loose dyes in clothes.
The load was not removed from dryer
at the end of the cycle.
The dryer was tightly packed.
For steam cycles, the water is not
properly connected with the dryer.
A Smart Grid event may have
interrupted the Steam Refresh cycle.
Recent painting, staining, or
varnishing in the area where your
dryer is located.
Separate the load to tumble freely.
The air outlet grille is just inside the door, behind the lint screen.
Check that it is not blocked by a fabric softener sheet.
Use only one fabric softener sheet, and use it only once.
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum of
1" (25 mm) of airspace, and, for most installations, the rear of the
dryer requires 5" (127 mm). See the Installation Instructions.
Level the dryer. See the Installation Instructions. All four dryer
feet should be in firm contact with the floor.
Under certain environmental or installation conditions, you may
experience underdrying.
When using the Steam Refresh cycle for a single item,
it is recommended to throw a towel in the dryer to prevent
damp spots.
Change the dryness level setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle. If loads are consistently ending
too early, see also "Changing the Automatic Cycle settings to
increase or decrease drying time."
Clean lint screen before each load.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Select Steam Refresh cycle to tumble the load with water and
heat. This cycle is best for smoothing out wrinkles and reducing
odors from dry loads consisting of wrinkle-free cotton, cotton-
polyester blends, common knits, and synthetics.
NOTE: Refer to garment care label instructions. Dry-clean-only
garments are not recommended.
Dry smaller loads that can tumble freely. Results may also vary
depending on fabric type.
Make sure water is connected to the dryer. Check that water
inlet hose is connected to both the faucet and dryer's water inlet
valve. Check that the water supply is turned on.
Rerun a Steam Refresh cycle. If necessary, turn off Smart Grid
monitoring during the cycle to prevent interruption.
Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
Solution