Whirlpool CED9150GW Руководство по установке - Страница 5
Просмотреть онлайн или скачать pdf Руководство по установке для Сушилка Whirlpool CED9150GW. Whirlpool CED9150GW 32 страницы. Commercial front-load washer
Печатать страницу
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter or in a
basement, laundry room, or recessed area. See "Drain System."
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need:
A water heater set to deliver 120°F (49°C) water to the
■
washer.
A grounded electrical outlet located within 6 ft (1.8 m) of
■
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water taps located within 4 ft (1.2 m) of the hot
■
and cold water fill valves, and water pressure of 20–100 psi
(137.9–689.6 kPa).
A level floor with a maximum slope of 1" (25 mm) under
■
entire washer. Installing the washer on soft floor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
A sturdy and solid floor to support the washer with a total
■
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage
in low temperatures.
Installation clearances
The location must be large enough to allow the washer
■
door to be fully opened.
Additional spacing should be considered for ease of
■
installation and servicing. The door opens more than
90° and is not reversible.
Additional clearances might be required for wall, door,
■
and floor moldings.
Additional spacing of 1" (25 mm) on all sides of the washer
■
is recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
■
Recessed area installation
This washer may be installed in a recessed area. The installation
dimensions shown are the minimum spaces allowable. Additional
spacing should be considered for ease of installation and
servicing. See the chart below.
Installation clearances
(Use recommended clearance for easier installation.)
Recessed/Undercounter
Recommended/Minimum
Back/Top
Sides
0"/0"
1"/0"
(0 mm)/(0 mm)
(25 mm)/(0 mm)
Washer Dimensions
50 ½"
(1282 mm)
Door is not reversible
*Height without leveling feet installed
NOTE: The door is not reversible.
A floor drain should be provided under the bulkhead. Prefabricated
bulkheads with electrical outlets, water inlet lines, and drain facilities
should be used only where local codes permit.
Drain System
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need.
See "Tools and Parts."
Standpipe drain system – wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe
of 2" (50 mm). The minimum carry-away capacity can be no
less than 12 gal. (45.5 L) per minute, per washer.
The top of the standpipe must be at least 30" (762 mm) high
and no higher than 96" (2.4 m) from the bottom of the washer.
A
27"
(686 mm)
44
5
(1134 mm)
*
"
37
/
13
16
(961 mm)
28
/
"
13
16
(732 mm)
30" min.
(762 mm)
B
*
/
"
8
5