Whirlpool 30 " Eye-Level Gas Range Руководство по установке - Страница 5

Печатать страницу

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and the wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

oven is properly grounded.

This oven must be connected to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and

all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial number rating

plate. The model/serial number rating plate is located under

the control panel on single ovens and under the control panel

on the upper oven cavity on double ovens. See the following

illustrations.

Single Oven

A. Model/serial number plate

Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to 7.4 kW at

208 volts) require a separate 40-amp circuit. Models rated at

4.8 kW and below at 240 volts (3.6 kW and below at

208 volts) require a separate 20-amp circuit.

A circuit breaker is recommended.

Electrical Requirements

Double Oven

A. Model/serial number plate

Connect directly to the circuit breaker box (or fused

disconnect) through flexible, armored or nonmetallic

sheathed, copper cable (with grounding wire). See "Make

Electrical Connection" section.

Flexible conduit from the oven should be connected directly

to the junction box.

Fuse both sides of the line.

Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

A UL listed or CSA approved conduit connector must be

provided.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the ends of the

flexible conduit leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

For power requirements for models WOS51EC7A, WOS51EC0A,

WOD51EC7A, WOD51EC0A, WOS92EC7A, WOS92EC0A,

WOD93EC7A, WOD93EC0A, MEW7527A, MEW7530A,

MEW7627A, MEW7630A, MEW9537A, MEW9627A, MEW9530A,

and MEW9630A, refer to the following table.

Voltage

Single

Thermal

240 VAC

3690 W

208 VAC

2790 W

240 VAC

15.4 A

208 VAC

13.4 A

For power requirements for models KEBK171B, KEBK101B,

KEBK276B, KEBK206B, KEBS179B, KEBS109B, KEBS277B,

KEBS279B, KEBS207B, and KEBS209B, refer to the following

table.

Voltage

Single

Thermal

240 VAC

4090 W

208 VAC

3099 W

240 VAC

17.1 A

208 VAC

14.9 A

Single

Double

Convect

Thermal

Convect

3720 W

7370 W

7400 W

2820 W

5580 W

5610 W

15.5 A

30.7 A

30.8 A

13.6 A

26.8 A

27.0 A

Single

Double

Convect

Thermal

Convect

4120 W

8170 W

8200 W

3122 W

6190 W

6212 W

17.2 A

34.1 A

34.2 A

15.0 A

29.8 A

29.9 A