Whirlpool RH3736XLQ3 Инструкции по установке и руководство по эксплуатации и уходу - Страница 4
Просмотреть онлайн или скачать pdf Инструкции по установке и руководство по эксплуатации и уходу для Вентиляционная вытяжка Whirlpool RH3736XLQ3. Whirlpool RH3736XLQ3 24 страницы. 30" (76.2 cm) and 36" (91.4 cm) range hood
Также для Whirlpool RH3736XLQ3: Список деталей (1 страниц), Инструкция по установке и руководство по эксплуатации и уходу (24 страниц)
Печатать страницуParts needed
For direct wire installation
•
UL listed or CSA approved 1/2"(12.5 mm) strain relief
•
75-watt max incandescent
light bulb
•
Power supply cable (if needed, for direct wire installation)
For power supply cord installation
•
UL Listed Power Supply Cord Connection
Kit marked for
range hood use.
•
75-watt max incandescent
light bulb
For vented installations
you also need:
•
31/4 '' x 10" (8.3 x 25.4 cm) or 7" (17.8 cm) round metal venting
•
7" (17.8 cm) round damper, if using 7" (17.8 cm) round vent
system
For cabinets with recessed
bottoms:
•
Two 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
•
Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
:::,:,
IMPORTANT: Observe all governing codes and ordinances.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located inside the range hood on
the rear wall.
•
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range
manufacturer installation instructions
before
making any cutouts.
•
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
•
The hood is factory-set
for vented installations. For non-
vented (recirculating) installations,
charcoal filter pad Part
Number 4396846 is available from your dealer.
•
All openings in ceiling and wall where range hood will be
installed must be sealed.
For Mobile
Home
Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
12"
J_
(30.5cm) 9"
1 1/2"
(2.5 cm)
(15._
29 7/_,,(75.9 cm) - 30" (7&2 cm) model
35 7A¢, ( 91.1 cm) - 36" (91.4 cm) mode(
I
17_/2
Installation
Clearances
,
opemn!
I
24" _61cm) m(n.
30
(76.2
cm)
suggested max.
bottom of cabinet
to cooking surface
18" (45.7 cm)
min.
c(eara_oe
upper cab(r_et
to countertop
35" (91.4 cm}
base cabine(
height
70 %e"
(178.6 cm)
76 %6"
cm)
max,
to bottom of
cabinet frame