Whirlpool WVW75UC6DS0 Инструкции по установке и руководство по эксплуатации и уходу - Страница 4
Просмотреть онлайн или скачать pdf Инструкции по установке и руководство по эксплуатации и уходу для Вентиляционная вытяжка Whirlpool WVW75UC6DS0. Whirlpool WVW75UC6DS0 28 страниц. 30" and 36" (76.2 and 91.4 cm) wall-mount canopy range hood
Печатать страницу
INSTALLATION REQUIREMENTS
tbo
Grid
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
Tools needed
•
Level
•
Drill with 11¼"(3.2 cm), 1/8"(3.2 mm), and 5Ae"(7.9 mm)
drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
Parts needed
•
Home power supply cable
•
1/2"(12.7 mm) UL listed or CSA approved strain relief
•
3 UL listed wire connectors
For vented installations,
you will also need:
•
1 wall or roof cap
•
Metal vent system
For non-vented
(recirculating)
installations,
you will also need:
•
Recirculation
Kit Part Number W10294733 for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
•
6" (15.2 cm) diameter round metal vent duct - length required
is determined by ceiling height.
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Hood canopy assembly with blower, LED lights and canopy
glass already installed.
•
Vent transition with back draft dampers installed
•
Metal grease filter
•
Vent cover support bracket
•
Mounting template
•
2-piece vent cover
•
Air deflector (for non-vented
[recirculating]
installations only)
•
4- 4.2 x 8 screws
•
6- 5 x 45 mm mounting screws
•
2 - 3.5 x 9.5 mm mounting screws
•
2 - 8 x 40 mm wall anchors
•
4- 10 x 50 mm wall anchors
•
T10 Torx ®t adapter
•
T20 ®tTorx ® adapter
1-®TORX,T10 and T20 are registered trademarks of Acument Intellectual Properties, LLC.
bsc@ on R!eq smen%
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
This range hood is recommended
for use with cooktops with a
maximum total rating of 60,000 BTUs or less.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented
(recirculating) installation see "For non-
vented (recirculating) installation only" in the "Connect Vent
System" section. Recirculation Kit Part Number W10294733 is
available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
20"
(50.8cm)
30" (76.2 crn) or
_36"
(91.4 crn)