FIRETECH FT-4X6 Series Руководство по эксплуатации - Страница 4

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Фонарик FIRETECH FT-4X6 Series. FIRETECH FT-4X6 Series 7 страниц. 4x6” headlights

INSTALLATION INSTRUCTIONS

1. Unscrew 6 Phillips screws holding headlight bezel in place. Remove and set aside bezel.

2. Remove 4 screws in headlight retaining ring. Remove old headlight bulb(s).

Tip: Start with 2 screws, then have a helper press the headlight into the housing while you remove the other 2

screws to prevent the headlight from falling out.

3. Repeat above steps for all 4 headlights prior to installing new fixtures.

4. Run a power wire from the marker light circuit on the apparatus to each of the headlight buckets. This will

be used to connect the halo power wires. Refer to video link below for more information.

5. Start by installing the High Beam headlights. These can be identified by the 2 pin connector and the letters

"VO" on the lens. High beam headlights must be installed in the "center" or "inboard" position on the

apparartus. Plug the connector into the factory wiring and attach the halo wire to the marker light circuit from

step 4 (above). Insert the body of the headlight into the mounting bucket and install the retaining ring using

the 4 screws removed in step 2. Be careful not to allow any connectors or terminals to come in contact with

the headlight mounting bucket.

6. Test operation of high beam headlights.

7. Once the high beam headlight function is validated, move on to installing the High/Low headlights. These

can be identified by the 3 pin connector and the letters "VOR" on the lens. High/Low headlights must be

installed in the "outer" position on the apparartus. Plug the connector into the factory wiring and attach the

halo wire to the marker light circuit from step 4 (above). Insert the body of the headlight into the mounting

bucket and install the retaining ring using the 4 screws removed in step 2. Be careful not to allow any

connectors or terminals to come in contact with the headlight mounting bucket.

8. Test operation of the headlight system. Click 1 of the headlight switch should turn on the halos, click 2

should turn on the low beams, cycling the high beam switch should disengage the low beams and engage

the high beams. If any problems exist, troubleshoot and/or contact HiViz for more information.

9. Reinstall headlight bezels from step 1. Be sure not to over-torque as this will cause cracking of the headlight

bezel assembly! Check for proper orientation prior to re-installation (look at adjustment screws).

10. Aim headlights per FMVSS108 requirements for a "VOR" headlight system.

11. Now that your new headlights are securely in place, you're vehicle is now ready for use.

HiViz LED Lighting HiViz Lighting INC PO Box 565, Naples, NC 28760 Phone: 703-662-3458 Email: [email protected]

Low Beam

High Beam

(outer light)

(inner light)

1. Remove 6 screws holding headlight trim ring in place.

Remove trim ring and set aside (be careful not to scratch it!)

3. Install the new fixtures per detailed instructions on opposite

page. Reinstall headlight retaining bezels.

HiViz LED Lighting HiViz Lighting INC PO Box 565, Naples, NC 28760 Phone: 703-662-3458 Email: [email protected]

2. Next, remove the 4 screws holding the headlight retaining

bezel to the housing. Remove the headlight(s).

4. Realign headlight trim ring and hand-tighten 6 retaining

screws so as not to crack the bezel. Note: bezel only goes one

way- aiming screws need to remain accessible.

5. Once reinstalled, aim headlights and test operations.