Ergo PrimeCables Cab-PC-08164 Руководство по установке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по установке для Внутренняя отделка Ergo PrimeCables Cab-PC-08164. Ergo PrimeCables Cab-PC-08164 2 страницы.

Печатать страницу

STEP 4

Connect All the Cables onto the

Control Box(8)

STEP 5

Install the Tabletop, Hand Switch(7) and Control Box (8)

x21

The control box need

to install on the

tabletop

The expansion of the supporting

beam can be adjusted according

to the actual use.

STEP 6-A

Install the Cable Management Tray (3)

Way 1

4x4

This marking indicates that this product should not be disposed with other household wastes.

To prevent possible harm to the environment or human health from uncontrolled waste

Waste disposal

disposal, recycle it responsibly to promote the sustainable reuse of material resources. To

return your used device, please use the return and collection systems or contact the retailer

where the product was purchased. They can take this product for environmental safe

recycling.

Power port

Port for cable

connected to the

Port for

lifting column

hand switch

H S M 1M2

M 3

Loosen

4x4

Pull

Tighten

Buckle in

Buckle in the

other side

Firstly, screw the screw (B) into the supporting beam (4) with Allen Key (F),

and not tighten completely. Buckle one side of the cable management tray (3)

into the screw (B), then press the other side into the screw (B). Finally, the

screw (B) is locked with Allen Key (F). The cable management tray (3) on

the auxiliary beam (5) are installed in the same way.

STEP 6-B

Install the Cable Management Tray (3)

Way 2

4x4

The Installation of cable management

tray (3) are installed in the same way

as Way 1 in Step 6-A.

How to use handswitch

Button

LED

display

"▲"

●

Adjust the desk upwards

"▼"

●

Adjust the desk downwards

"1"

●

Position 1, first height position saved by user

"2"

●

Position 2, second height position saved by user

"3"

●

Position 3, third height position saved by user

"M "

●

Memory button for height memory function

"A "

Alarm button for reminding of keeping same

●

position for long time

Common fault treatment

The following tips will help you detected and eliminate the common fault

and error.If the fault you met is not listed below, please contact with your

supplier. Only themanufacturer and professionals are capable for investigating

Tighten

and correcting those fault and error.

Fault phenomenon

No response while long pressing

down arrow after connected with

a power supply

No response while pressing up

arrow/ down arrow after

connected with a power supply

Rising in a low speed

The motor not move as instructed

Go down but not go up

Downward sliding

Frequently Reposition

Overwork

（Duty cycle:Max 2min on/18min OFF）

Not enough up&down height

The cable management tray (3) should be

mounted on the middle connecting rod when

the frame is stretched more than 1720 mm.

The length of the supporting

beam should not exceed this

hole position.

Instruction

• Press the UP button or DOWN button to lift or lower the height of desk surface. The LED display

shows the real time value. The range of the height value: 58.0cm-123cm.

• Saving A Height Position

a. Press the UP button or DOWN button to lift or lower the height of desk surface. For instance, you

adjust the height to 80cm.

b. Press "M" SAVE button and the LED display shows" ", then press "1" to save the 1st height

position to 80cm. The LED display shows "

c. Repeat step a and step b to save the 2nd height position to 100cm The LED display shows "

Save the 3rd height position to 120cm The LED display shows "

d. Press "1", "2","3", to automatically reach the height saved before.

• Long-Time Sitting Reminder

a. Press REMINDER button "A" to activate the function. The LED display shows " "

b. Two seconds later, press the "▲" or "▼" button to adjust the reminder time only when the display

screen flashes. Then press any button to save the time setup, or wait 5 seconds and system will

save the time setup automatically. During the countdown, any operation will lead to a repeat

starting of the timer. When the countdown finishes, the buzzer will be active with a 10-second

"DiDi...DiDi...DiDi..."tone.

c. Within the 10-second reminder buzz, press any button to reactivate the time countdown that is

set up in (b) step. If no operation during the 10-second reminder buzz, there will be another

reminder buzz after 5 minutes. No operation during the second buzz will turn off the Long-Time

Sitting Reminder.

d. Press and hold the "A" button for three seconds to turn off the Long-Time Sitting Reminder. The

LED display shows "

Attention

1. Power supply: AC100V-127V/200V-240V,50/60Hz

2. Service Environment: 0-40℃

3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet

dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose

Method

the connector.

1.Check if all the cables be connected well

4. The electric box contains electronic components, metals, plastics, wires etc., so

dispose of it in accordance with each country's environmental legislation, not the

2.Contact your supplier or dealer

general household waste.

1.Check if all the cables be connected well

5. Check carefully to ensure correct and complete assembly before using.

6. Be familiar with all functions and program settings of the product before first use.

2.Contact your supplier or dealer

7. Children are forbidden to play on the product because of unforeseen action when

Check if overloaded, max loading: 150kg;

playing, so any dangerous consequences caused by this improper action will not be on

8. Slight noise caused by the V-ribbed belt or brake system due to structure will not

Contact your supplier or dealer

have any effect on the use of the equipment.

1. Contact your supplier or dealer

9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure

that the cleaner used will not pollute the environment.

1.Reposition

10. This appliance can be used by children aged from 8 years and above and persons

2.Contact your supplier or dealer

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

Check if overloaded, max loading: 150kg;

appliance in a safe way and understand the hazards involved. Children shall not play

Contact your supplier or dealer

with the appliance.

11. Cleaning and user maintenance shall not be made by children without supervision.

Check if overloaded, max loading: 150kg;

12. If the supply cord is damaged, it must be replaced by the manufacturer, its service

Contact your supplier or dealer

agent or a similarly qualified person in order to avoid a hazard.

Restart after suspend for 18mins while

13. Please make sure there is no hazard sources in your operating environment. e.g.,

connecting with power;

do not litter the tools around. Always be careful to treat the packaging materials in order

Contact your supplier or dealer;

to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.

14. Keep the original package of the equipment if necessary in case of the future use in

1. Press "M"and "3" together for 3 seconds or

more, after hearing continuous beeping for twice,

transportation.

it will restore factory settings

2.Contact your supplier or dealer