Clarion DCZ625 Руководство пользователя - Страница 2

Просмотреть онлайн или скачать pdf Руководство пользователя для CD-плеер Clarion DCZ625. Clarion DCZ625 8 страниц. 6 disc cd changer with cd text
Также для Clarion DCZ625: Брошюра и технические характеристики (6 страниц), Руководство пользователя (1 страниц), Руководство по установке и подключению проводов (10 страниц), Руководство по эксплуатации (11 страниц)

Печатать страницу

3. Remove the floor carpet and decide on the place

to install. Adjust the installation bracket with bolts

to suit the place of installation.

7. Align the unit with the bolts and secure it with the

wing nuts.

4. Remove the separator of the cushion rubber that

is attached to the installation bracket with bolt and

install accordingly.

5. Unfasten the wing nut and remove the unit.

6. Return the floor carpet to its original place. Use a

knife to cut into the carpet where the bolt can be

felt, and allow the bolt to protrude from the carpet.

"II

TROUBLESHOOTING

If the same phenomenon still occurs after checking the above, or it is impossible to remove the magazine, please

consult your local dealer.

Installation Procedure

1. Use the double seamed hexagonal bolts to fix

installation bracket to the unit (on both sides) in

the desired direction of installation.

2. Use the wing nut to hold in place the installation

bracket with bolt to the installation bracket, which

is attached to the unit. Then affix the cushion rub-

ber.

Symptom

Cause

Remedy

Loss of power

Bad connection.

Check connections. Connect the cable again.

Connection with

the source unit is The length of the CeNET Rewire the connection so that the length of cable is less than 65.62 It

not recognized.

cable wiring is more than (20m).

65.62 It (20m).

Address switch num- When the 2 CD changers are connected, set the address switch so

bers are the same.

that they do not have the same address number. Refer to the "Exam-

ple of address switch setting" in the section titled "IDENTIFICATION

OF PARTS".

Magazine cannot Magazine inserted Insert correctly.

be loaded.

wrongly.

A magazine is already Eject the magazine and insert the other.

in the player.

Distorted magazine.

Buy New Magazine CAA-397.

"No Disc" sign

Disc inserted upside- Read the section on "Inserting The CD" carefully and reinsert the CD

appears when

down.

correctly.

searching for

discs.

Moisture or dirt on disc. Wipe disc free of moisture and dirt.

Noise, skipping

The installation selec- Set the installation selector levers to the same position on both sides.

tor levers are set to dif-

ferent positions on both

sides.

The unit installation di- Set the unit installation direction and the installation selector lever

rection and the instal- positions to match each other. When installed at an angle, change the

lation selector lever po- installation selector lever to a position (H, 45", V) not prone to noise or

sitions do not match.

sound loss.

Disc bent or badly Compare with another disc. If bad, discard the damaged disc.

damaged.

Disc is very dirty.

Clean the disc.

Mechanism does Mechanical error.

1. Referring to section "INSTALLATION", check the three angle of in-

not function.

stallation selector levers are properly set. If not, set them at the

proper position for the angle of installation.

2. Check whether The CD magazine can be ejected by pressing the

CD magazine eject button, then insert a new CD magazine.

Magazine is

Disc holder is not cor- Read the section on "Inserting the CD" carefully and reinsert the disc

ejected evenwhen

rectly inserted into the holder correctly.

inserted into the

magazine.

unit.

Digital optical fiber cable

(Sold separately)

Digital optical fiber cable

(Sold separately)

Ferrite clamp

(Included the MD changer)

MD changer

- [

V-adapter

(CCA-519: Sold separately)

OCZ6Z5

~~/

=:::::::J===l

• Dust and other objects may cause malfunc-

tions if they get into the unit.

Always be sure to shut the flip down door once

finished with loading or unloading the maga-

zine.

- Before shipment from the factory, the levers are nor-

mally placed in the horizontal position .

2. Decide on the installation place and direction.

3. Insert an item such as a screwdriver with a fine

point or the tip of a ballpoint pen into the round

hole of the installation selector lever to switch to

the position you need.

CeNETcable

(Included the DCZ625)

CeNETcable

(Included the DCZ625)

CD deck or MD deck

Souce

.....,.....,,.....,,.....,,.....,...,+,.....,...

CeNET cable

(Included the Clarion expanded digital

sound processor / equalizer DSP/EQ)

• FULL SYSTEM

• STANDARD SYSTEM

Eject button

Note:

• Reinstall these lock pins when shipping the unit back

for repair.

Note:

Only the provided screws and brackets should be used during installation. Us-

ing screws other than those specified will cause damage.

• When connecting the CeNET cable, fully insert it. Alter connection, fix

the connector with a c1amper as shown in the figure.

• When removing the digital optical fiber cable, rotate it to loosen it and

pull it gently while holding the slide cap (a gray color part on the source

unit).

• Do not coil up the digital optical fiber cable with a radius of less than 1"

(3 cm). With a radius of less than 1", the performance of the cable will

be greatly impaired.

• When installed in a glove box or console box, make sure that the source

unit cables or cords do not interfere with the opening or closing of the

flip down door.

Extracting the Magazine

1. Open the flip down door.

2. Press the eject button and take out the magazine.

INSTALLATION

CONNECTORS

SYSTEM EXAMPLE

This unit is available for upgrade in various ways.

When you want to upgrade the system, make sure that the upgrade unit fits and wire it correctly.

Prior to Installation

1. Before attempting to use this unit you must first

remove the packing safety lock pins (3 posi-

tions). Store these lock pins carefully so they

can be used again if needed.

INSTALLATION

SPECIFICATIONS

H: Horizontal

45": Slope

V: Vertical

45°

...-

Align the installation selector le-

vers on both sides of the unit with

the "H" position.

the "45°" position.

the "V" position.

Frequency Response

Signal-to-Noise Ratio

Wow and Flutter

Power Supply

Current Consumption

Unit Weight

Dimensions

: 5Hz-20kHz(±ldB)

: 105dB(1 kHz)IHF'A

: Below measurement limits

: DC14.4V (1 O.8-15.6V) negative ground

: Less than 1A

: 3.6Ib. (1.65kg)

: 8-7/8"(Width) x 2-1/2" (Height) x 6-9/16"(Depth)

[225mm(W) x 63mm(H) x 167mm(D)]

• Set the installation selector lever to the same position on both sides.

• When the unit is installed below the horizontal position (up to 15 degrees) the ejected magazine,

when left in that position, will drop due to vibrations from the car.

• Adjust the installation selector levers into the correct locations. Setting the locations incorrectly or

in varied positions will cause skipping.

• Do not move the installation selector levers while the unit is in use. This will cause damage to the

mechanism and the disc.

-Due to improvements, the design and these specifications may be modified without prior notice.

Clarion

Co.,ltd.

Printed in China

2001/6

(T.C)

PE-24338 280-7715-00